Discharge Chute Deflector
ALWAYS position discharge chute deflector at
Differential Lock (924117, 300, 505,
506, 508)
a safe angle before starting engine.
DO NOT throw snow any higher than
necessary.
Push deflector handle forward or down to
throw snow lower. Pull deflector handle up or
to the rear to throw snow higher.
IMPORTANT: If Chute Deflector does not stay
in set position, adjust as directed in Service
and Adjustments, or repair before operation.
Differential Lock knob is located
on the Left Wheel Hub. With
differential locked power is
applied equally to both wheels.
To engage differential lock:
1
2
•
Pull and turn knob to LOCKED
position and release (knob
(1)
will snap in place when
positioned correctly).
OL2730
Deflector Remote (924116, 505, 506)
To resume differential action for
transport:
Place deflector into position before operation.
DO NOT throw snow any higher than
necessary.
•
Pull and turn knob to UNLOCKED (2)
position and release.
Push deflector remote forward to throw snow
lower. Pull deflector remote back to throw
snow higher.
Axle Lock Pin (924116)
The axle lock pin is located on the right wheel
hub. Moving pin from the hub to the axle shaft
allows the right wheel to turn freely.
Discharge Chute
Discharge chute rotates 220°.
Scraper Blade
ALWAYS position discharge chute in safe
direction and angle, away from operator and
bystanders, before starting engine.
The scraper blade allows the back of the
housing to keep better contact with the surface
being cleared. It also prevents damage to the
housing from normal wear.
Chute Crank (924116, 117, 300, 508)
IMPORTANT: If chute does not stay in set
position, adjust as directed in Service and
Adjustments, or repair before operation.
IMPORTANT: DO NOT allow Scraper Blade to
wear too far or Auger/Impeller housing will
become damaged.
Rotate the Chute with Discharge Chute Crank
Handle.
IMPORTANT: DO NOT force frozen chute
controls. Start engine and run for 3-5 minutes
to thaw. If still frozen, take to warm place until
controls are free.
Runners
The runners control the distance between the
scraper blade and the ground. Adjust runners
equally to keep blade level with the ground.
Refer to Pre-Start for recommended settings.
Chute Rotation Switch (924505, 506)
FILLING FUEL TANK
2
1
WARNING: AVOID INJURY. Read
and understand Fuel Safety Rules in
Safety section before proceeding.
OS1970
To add fuel to fuel tank:
Press the chute rotation switch right (1) to
rotate chute clockwise. Press the chute
rotation switch left (2) to rotate chute
counterclockwise.
1. ALWAYS place unit in open or well
ventilated area.
2.
3.
Stop engine and allow to cool.
Clean Fuel Cap and surrounding area to
prevent dirt from entering Fuel Tank.
Heated Handles
Turn the heated handles
switch to the ON (1) position
to activate. Turn the switch
to the OFF (2) position to
4. Remove Cap.
1
IMPORTANT: DO NOT use gasohol or
gasoline containing alcohol. See Engine
Manual for correct type and grade of fuel.
deactivate.
5. Fill fuel tank to within 1/2" (1,2 cm) below
bottom of filler neck with unleaded
gasoline.
2
OS1950
GB - 16
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 1024, Ariens 1028, Ariens 1128, Ariens 1332, Ariens 1336, Ariens 924116, Ariens 924117, Ariens 924300, Ariens 924505, Ariens 924506, Ariens 924508 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)