NOTE: 924116 tank capacity is 1 gallon
7. Check Engine Fuel & Crankcase Oil
(3.8
liters). Tank capacity of other models is
quarts (3,3 liters).
3.5
WARNING: AVOID INJURY. Read
and understand Fuel Safety Rules in
Safety section before proceeding.
6.
Replace Fuel Cap and tighten.
7.
ALWAYS clean up any spilled fuel.
PRE-START
Check and add fuel if required. Check that the
engine crankcase oil is full using dipstick.
Refer to Engine Manual for detailed
instructions.
1.
Frozen Impeller
IMPORTANT: Before starting engine, check
impeller to be sure it is not frozen.
To check impeller:
TO STOP IN AN EMERGENCY
1.
With key in “Stop” position, squeeze
Attachment Clutch Lever to Engaged
position.
Immediately release both control levers to stop
unit in an emergency. Stop engine, remove
key and wait for all rotating parts to stop before
leaving operator’s position.
2.
3.
Pull Recoil Starter Handle.
If Impeller is frozen, (cannot pull Starter
Handle) move unit to a heated area and
thaw to prevent possible damage.
STARTING AND SHUT OFF
2.
Auger and impeller must stop quickly when
attachment clutch lever is released.
Wheels must stop quickly when traction drive
clutch lever is released.
If clutches do not engage or disengage
properly, adjust or repair before operation (see
Service and Adjustments).
Check Function of Clutches
WARNING: FAILURE TO FOLLOW
INSTRUCTIONS could result in
personal injury and/or damage to
unit. DO NOT attempt to start your
unit at this time. Read entire Owner/
Operator Manual and the Engine
Manual first.
IMPORTANT: Allow unit and engine to adjust
to the outdoor temperatures before clearing
snow. Before shut-off, run the attachment a
few minutes to prevent freeze-up.
NOTE: Try out each control without the engine
running to see how it works and what it does.
3.
Check Dual Handle Interlock
Without the engine running, press down
(engage) both clutch levers. Release
attachment clutch lever. Attachment clutch
should remain engaged until traction clutch
lever is released, then both clutches must
disengage.
Manual Start
1. Turn discharge chute straight ahead.
4.
Differential Lock (924117, 300, 505,
2. Make sure that the traction clutch and
attachment drive clutch levers are fully
disengaged.
506,
508)
ALWAYS engage differential lock (located in
left wheel hub) for best traction when throwing
snow.
3.
Push Primer Bulb 2 or 3 times for cold
engine.
NOTE: When temperature is below -15˚ F
(-26˚ C) additional priming may be needed.
5.
Adjust Axle Lock (924116)
Keep locking pin on the right wheel hub for
best traction when throwing snow.
4. If engine is cold, apply choke. See Engine
Manual for detailed instructions.
NOTE: A warm engine requires less choking
6.
Adjust Runners
than a cold engine.
Check and adjust Runners (see Service and
Adjustments). Allow 1/8" (3mm) between
scraper blade and hard, smooth surface(s).
Allow 1-1/4" (30mm) between scraper blade
and uneven or gravel surfaces.
5.
Set throttle to proper starting position.
6.
Insert key into ignition switch.
12V - Turn key into RUN position.
120V - Push key into RUN position. DO
NOT twist key after it is inserted.
7.
8.
Grasp starter handle and pull rope out
slowly until it pulls harder. Let rope rewind
slowly.
Pull rope with a rapid continuous full arm
stroke. Let rope rewind slowly.
GB - 17
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 1024, Ariens 1028, Ariens 1128, Ariens 1332, Ariens 1336, Ariens 924116, Ariens 924117, Ariens 924300, Ariens 924505, Ariens 924506, Ariens 924508 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)