CHECK DUAL HANDLE
INTERLOCK
Gear cases are filled to the correct level at the
factory. Unless there is evidence of leakage,
no additional lubricant should be required.
Check oil level each season or every 25 hours
of operation.
Without the engine running, press down
(engage) both clutch levers. Release
attachment clutch lever. Attachment clutch
should remain engaged until traction clutch
lever is released, then both clutches must
disengage.
To ensure adequate lubricant level:
1. Remove filler plug (Figure 14). Lubricant
must be at least up to bottom of lubricant
filler hole with unit resting on a
level-surface.
CHECK FASTENERS
2. Add lubricant if required. Allow oil to drain
to level of plug and replace plug.
Make sure all hardware is tightened properly.
CHECK CLUTCHES
IMPORTANT: Use only Ariens special gear
lubricant L-2 (Part Number 00008000).
Auger / impeller must stop within 5 seconds
when attachment clutch/impeller brake lever is
released.
1
Wheels must stop quickly when traction drive
clutch lever is released.
3
If clutches do not engage or disengage
properly, adjust or repair before operation (see
Service and Adjustments).
CLEAN ENGINE
Refer to Engine Manual for detailed
instructions.
2
CHECK ENGINE OIL
The engine crankcase oil should be checked
every 5 hours of operation. Oil level MUST be
maintained in safe operating range on dipstick
at all times or engine damage will result (See
Engine Manual).
1. Auger Gearcase - Cast Iron
2. Oil Fill and Drain Plug
3. Auger Gearcase - Aluminum
Figure 14
Park unit on a level surface. Refer to Engine
Manual for detailed instructions.
GENERAL LUBRICATION
IMPORTANT: Wipe each fitting clean before
and after lubrication.
IMPORTANT: DO NOT allow grease or oil to
get on friction disc, friction plate or belts.
NOTE: Apply Stens Mix Hi-Temp Grease or
equivalent to the lubrication fittings. See
Service Parts.
CHANGE ENGINE OIL
Change oil after first 2 hours of operation,
thereafter change oil every 25 hours (more
often if required). Refer to Engine Manual for
detailed instructions.
Run engine just prior to changing oil. Warm oil
will flow more freely and carry away more
contamination. Remove the oil drain plug from
the rear of the unit and tip the unit back to help
drain all the oil.
Sno-Thro should be lubricated (Figure 15) at
beginning of season or every 25 operating
hours.
Auger Shaft
NOTE: To grease auger shaft, remove shear
bolt nuts, and shear bolts. Turn auger on shaft
while applying grease at zerk fittings. Replace
shear bolt per instructions in Service and
Adjustments.
CHECK TIRE PRESSURE
Keep tires at pressure listed on the tire
sidewall.
CHECK AUGER GEARCASE
IMPORTANT: Proper oil level must be
maintained.
GB - 20
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 924124, Ariens 924125, Ariens 924126, Ariens 924127, Ariens 924128, Ariens 924335, Ariens 924336, Ariens 924337, Ariens 924338, Ariens 924516, Ariens 924517, Ariens ST11526DLE, Ariens ST11528DLE, Ariens ST11528LE, Ariens ST1332DLE, Ariens ST1332LE, Ariens ST1336DLE, Ariens ST1336DLE Ariens 924124, Ariens ST926DLE |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)