ATTACHMENT CLUTCH/BRAKE
ADJUSTMENT
a.Loosen the idler adjustment nut.
b.To increase spring extension, move
idler towards belt (Figure 24).
(Figures 21 and 22)
c.To decrease spring extension, move
idler away from belt.
IMPORTANT: IMPROPER
ADJUSTMENT could result in
unexpected movement of auger and
impeller causing death or serious
injury. Auger / impeller must stop
within 5 seconds when Attachment
Clutch/Impeller Brake lever is
released.
d.Tighten idler adjustment nut.
7. Place unit in service position. Remove
bottom cover by removing four cap
screws.
8. Check brake.
When the clutch lever is disengaged, the
brake must contact attachment belt.
1. Remove belt cover.
When the clutch lever is engaged, the
brake must be more than 1/16 in.
2. Check belt alignment (Figure 24).
Engine sheave and attachment pulley
must align vertically. Also, belt must be
centered in the idler pulley.
(1.6
mm) away from the belt (Figure 22).
9. Repeat steps 4 – 7 until:
Spring stretch and brake contact are
correct.
To align, move attachment pulley:
a.Loosen set screws.
10. Check belt finger clearance (Figure 24).
b.Slide pulley and key to desired
position.
With clutch lever engaged, belt fingers
should be 1/16 – 1/8 in. (1.6 –3 mm) from
belt. Adjust belt fingers as necessary.
c.Tighten set screws.
3. Install belt cover.
11. Replace bottom cover.
4. Adjust cable slack.
IMPORTANT: The belt cover must be installed
and the clutch cable must be slack when the
lever is disengaged.
7/16–11/16 in
(11.1-17.5 mm)
a.With clutch lever disengaged, loosen
jam nut on cable adjuster.
9
10
b.Turn adjuster body to remove all slack
from the cable. Do not stretch spring
or move lower clutch arm.
c.Turn back the adjuster body 5 turns
(approximately 1/4 in. or 6 mm).
Finger tighten jam nut.
d.Hold adjuster body with pliers and
tighten jam nut with wrench.
5. Check spring length.
a.Measure the length of the clutch cable
spring.
b.Engage and hold the attachment
clutch lever.
8
2
4
6
5
3
1
7
c.Measure the length of the spring
again. The spring should be
1.Attachment
Clutch Cable
2.Cable Adjuster
3.Jam Nut
4.Clutch Cable
Spring
6.Shift Arm
7/16
–11/16 in. (11.1–17.5 mm) longer
7.Cotter Pin and
when the lever is engaged.
Washer
6. Adjust spring length.
8.Adjustment Nut
9.Traction Drive
Clutch Cable
10.Shift Rod
NOTE: Approximately 1/8 in. (3 mm)
movement of the idler will change spring
extension by 1/8 in. (3 mm).
5.Lower Clutch Arm
Figure 21
OS3040
GB - 24
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 924124, Ariens 924125, Ariens 924126, Ariens 924127, Ariens 924128, Ariens 924335, Ariens 924336, Ariens 924337, Ariens 924338, Ariens 924516, Ariens 924517, Ariens ST11526DLE, Ariens ST11528DLE, Ariens ST11528LE, Ariens ST1332DLE, Ariens ST1332LE, Ariens ST1336DLE, Ariens ST1336DLE Ariens 924124, Ariens ST926DLE |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)