5. Release traction clutch lever, shift to third
(3) position, and remove friction disc.
SHORT TERM
IMPORTANT: NEVER spray unit with high
pressure water or store unit outdoors.
Run with attachment clutch engaged a few
minutes after each use to free unit of any loose
or melting snow.
6. Secure new friction disc on hub with five
cap screws and torque cap screws to
8-10 lbf-ft (10,6-13,3 N•m).
7. Replace bottom cover.
8. Adjust traction drive clutch (see Traction
Close fuel shut-off valve.
Drive Clutch Adjustment).
Inspect unit for visible signs of wear, breakage
or damage.
1
2
3
Keep all nuts, bolts and screws properly
tightened and know unit is in safe working
condition.
6
Store unit in a cool, dry protected area.
LONG TERM
Clean unit thoroughly with mild soap and low
pressure water and lubricate (see
Maintenance). Touch up all scratched painted
surfaces.
OS0612
Remove weight from wheels by putting blocks
under frame or axle.
5
4
4. Shift Arm
When storing unit for extended periods of
time, remove all fuel from tank and carburetor
(run dry). Refer to Engine Manual.
1.
2.
3.
Cap Screw
Cotter Pin
Friction Disc
5. Chain
Idler Hex Shaft
SERVICE PARTS
Figure 25
Order the following parts through your Dealer:
BATTERY (924516, 517)
Charging
Part No.
Description
00036800
Stens Mix Hi-Temp Grease (3, 3 oz.
cartridges)
1. Place unit on a level surface and shut off
engine.
21533500
07200005
Spark Plug
2. Disconnect negative (-) cable first, then
positive (+) cable.
Impeller Belt (924128, 338, 516,
517)
3. Loosen wing nut and remove battery.
Place battery on bench or other well
ventilated place.
07200004
07211200
07236100
Impeller Belt (924124, 125, 126,
127, 335, 336, 337)
4. Connect positive (+) lead of charger to
positive (+) terminal, and negative (-) lead
to negative (-) terminal.
Traction Belt (124, 125, 126, 127,
335, 336, 337)
Traction Belt (924128, 338, 516,
517)
5. Charge the battery at two and a half amps
for ten hours.
00170800
51001500
Friction Disc
6. Reinstall battery into unit and connect
positive (+) cable first, then negative (-)
cable.
Shear Bolt Kit
To obtain a complete parts manual, find your
model and serial number. Then go to
www.ariens.com or call 1-920-756-4664.
Replacing
Use U1R or U1L; 340 to 350 CCA @ 0°F type
batteries.
ACCESSORIES
See your authorized Ariens dealer to add the
additional accessories available to your
Sno-Thro.
STORAGE
Part No.
Description
WARNING: AVOID INJURY. Read and
understand the entire Safety section
before proceeding.
72406500
Front Weight Kit
GB - 27
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 924124, Ariens 924125, Ariens 924126, Ariens 924127, Ariens 924128, Ariens 924335, Ariens 924336, Ariens 924337, Ariens 924338, Ariens 924516, Ariens 924517, Ariens ST11526DLE, Ariens ST11528DLE, Ariens ST11528LE, Ariens ST1332DLE, Ariens ST1332LE, Ariens ST1336DLE, Ariens ST1336DLE Ariens 924124, Ariens ST926DLE |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)