MTD 600 Series K Style Snow Blower Owners Manual

Fuel Recommendations
Checking Oil Level
Use automotive gasoline (unleaded or low leaded to minimize
combustion chamber deposits) with a minimum of 87 octane.
Gasoline with up to 10% ethanol or 15% MTBE (Methyl Tertiary
Butyl Ether) can be used. Never use an oil/gasoline mixture  or
dirty gasoline. Avoid getting  dirt, dust, or water in the fuel tank.
DO NOT use E85 gasoline.
CAUTION: The engine is shipped with  oil in the
engine. You must, however, check the oil level prior
to operating the snow thrower. Running the engine
with insufficient oil can cause  serious engine
damage and void the engine warranty.
NOTE: Be sure to check the engine on a level surface with the
engine stopped.
Refuel in a well-ventilated area with the engine  stopped.
Do not smoke or allow flames or sparks  in the area where
the engine is refueled or where gasoline  is stored.
1
.
Remove the oil filler cap/dipstick and wipe the dipstick
clean. See Fig. 3-9.
Do not overfill the fuel tank.  After refueling, make sure the
tank cap is closed properly and securely.
2
.
Insert the cap/dipstick into the oil filler neck,  but do not
screw it in.
Be careful not to spill fuel when refueling.  Spilled fuel or
fuel vapor may ignite. If any fuel is spilled,  make sure the
area is dry before starting  the engine.
Avoid repeated or prolonged contact  with skin or
breathing of vapor.
Adding Fuel
WARNING!  Use extreme care when  handling
gasoline. Gasoline is extremely  flammable and the
vapors are explosive.  Never fuel the machine
indoors or while the engine is hot or running.
Extinguish cigarettes, cigars,  pipes and other
sources of ignition.
Fill
between
high
and low
marks
WARNING! Always keep hands and feet clear of
equipment moving parts. Do  not use a pressurized
starting fluid. Vapors are  flammable.
1.
Clean around fuel fill before removing  cap to fuel.
2
.
A fuel level indicator is located in the fuel  tank. Fill tank
until fuel reaches the fuel level indictor, Fig. 3-8.  Be careful
not to overfill.
Figure 3-9
3
.
.
Remove the oil filler cap/dipstick. If the level is low, slowly
add oil until oil level registers between  high (H) and low
(L), Fig. 3-9.  Refer to the Engine Maintenance section  for
correct oil viscosity and engine  oil capacity.
NOTE: Do not overfill. Overfilling  with oil may result in
engine smoking, hard starting  or spark plug fouling.
4
Replace and tighten cap/dipstick firmly before starting
engine.
Fuel Level Indicator
Top View
Tire Pressure
Before operating, check tire pressure and reduce  pressure in both
tires to between 15 psi and 20 psi.
NOTE: If the tire pressure is not equal in both tires, the machine
may not travel in a straight path and the shave plate may wear
unevenly.
Figure 3-8
sectiOn 3 — asseMbly & set-up
9
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website