MTD E662H E642E 614E E644E E664F E6A4E Snow Blower Owners Manual

4.
Place  one  flat  washer  on  the  end  of  the  chute
crank,  then  insert  the  end  of  the  crank  into  the
hole  in  the   plastic  bushing  in  the  chute   crank
bracket. See Figure 17.
FINAL ADJUSTMENTS
Auger Drive Clutch
1.
2.
3.
To check the adjustment of the auger drive clutch,
push   forward    on   the   left    hand   clutch    grip
depressing  the  rubber  bumper  under  the  clutch
grip. There should be slack in the cable.
Flat Washer
Chute Crank
Release  the   clutch  grip.  The   cable  should  be
straight. Make certain you can depress the auger
drive    clutch    grip    against     the    left    handle
completely.
Hairpin Clip
Chute Crank
If  necessary,  loosen  the  hex  jam  nut  and  thread
the cable in (for less slack) or out (for more slack)
as  necessary.  Refer  to  Figure  13.  Recheck  the
adjustment. Tighten the jam nut against the cable
when correct adjustment is reached.
Bracket
Figure 17  
5.
6.
7.
Place the other flat washer on the end of the chute
crank, and insert hairpin clip into hole in the end of
crank. See Figure 17.
Traction Drive Clutch and Shift Lever
Adjustment
Adjust the chute bracket so that the spiral on the
chute crank fully engages the teeth on the chute
assembly.
To  check  the  adjustment  of  the  traction  drive  clutch
and shift lever:
Tighten the nuts on the lower chute crank bracket
securely.  Tighten  the  hex   bolt  and  nut  on  the
upper chute crank bracket on the handle.
1.
Move  the  shift  lever  all  the  way  to  the  highest
speed. With the traction drive lever released, push
the  snow  thrower  forward.  The  unit   should  roll
forward.
LAMP WIRING (If Equipped)
2.
3.
Then  engage  the  traction  drive  clutch  grip.  The
wheels should stop turning.
Lamp Wire
Alternator
Lead
Now  release  the  traction  drive  clutch  grip,  and
push the unit again. Move the shift lever back to
the fast reverse position, then all the way forward
again. There should be no resistance in the shift
lever, and the wheels should keep turning.
Right Handle
4.
If you have resistance when moving the shift lever
or the wheels stop when they should not, loosen
the   jam  nut   on   the  traction   drive   cable  and
unthread the cable one turn. If the wheels do not
stop  when  you  engage  the  traction  drive  clutch
grip, loosen the jam nut on the traction drive cable
and  thread  the  cable  in  one  turn.  Recheck  the
adjustment and repeat as necessary.
Figure 18  
1.
Wrap  the   wire  from   the  lamp   down  the   right
handle  until  the   wire  can  be   plugged  into  the
alternator    lead   wire  under  the  fuel  tank.   See
Figure  18.  Be  sure  lamp  wire  does  not  interfere
with the movement of any controls or cables.
5.
Tighten  the  jam  nut  to  secure  the   cable  when
correct adjustment is reached.
IMPORTANT:   After  attaching   the  shift  rod   and
clutch  cables,  check  the  adjustments  as  instructed,
and  make  any   final  adjustments  necessary   before
operating  your  snow   thrower.  Failure  to  follow  the
instructions may cause damage to the snow thrower.
NOTE: If  you  are  uncertain  that  you  have  reached
the    correct    adjustment,   refer    to    SECTION    8:
ADJUSTMENTS.
10
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals
Tags, , , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website