MTD E662H E642E 614E E644E E664F E6A4E Snow Blower Owners Manual

TO ENGAGE DRIVE/AUGER
WARNING: Temperature of muffler and
surrounding  areas  may  exceed  150  F.
Avoid these areas.
1.
With the engine running near top speed, move
shift   lever   into   one   of   the    FORWARD   or
REVERSE positions. Select a speed appropriate
for  the   snow   conditions  that   exist.  Use   the
slower  speeds  until  you   are  familiar  with  the
operation of the snow thrower.
o
For   most   efficient  snow   removal,   remove
snow immediately after it falls.
Discharge
snow
downwind
whenever
2.
3.
Squeeze  the   left  hand  auger   drive  clutch  to
engage auger.
possible.    Slightly   overlap    each    previous
swath.
While   the   left   hand   auger    drive   clutch   is
engaged,  engage  the  right  hand  traction  drive
clutch.
Set the skid shoes 1/4" below the scraper bar
for  normal  usage.  The   skid  shoes  may  be
adjusted upward for hard-packed snow. Adjust
downward  when  using  on  gravel  or  crushed
rock.
NOTE: NEVER   move    shift   lever   without    first
releasing the drive clutch.
Be  certain   to  follow   the  precautions   listed
under ‘‘To Stop Engine’’ in previous column to
prevent possible freeze-up.
TIRE CHAINS (OPTIONAL):
Use tire chains when extra traction is necessary.
Clean the snow thrower thoroughly after each
use.
OPERATING TIPS
NOTE: Allow  the  engine   to  warm  up  for  a   few
minutes  as  the  engine  will  not  develop  full  power
until it reaches operating temperature.
SECTION 8:  ADJUSTMENTS
WARNING: Never   attempt   to    clean
chute  or  make  any  adjustments  while
engine is running.
ADJUSTING SKID SHOE
The space between the shave plate and the ground
can be adjusted by adjusting the skid shoe. Slide the
skid shoe upwards and lower the housing to remove
snow   close    to    the   ground.    Slide   skid    shoe
downwards  and  raise  the  housing  to  remove  snow
from  uneven  ground  like  gravel.  For  more  details,
refer to Adjusting the Skid Shoes in section 5.
ADJUSTING CHUTE
You can control the distance that snow is thrown by
adjusting  the   angle  of   the  chute  assembly.   The
sharper the angle, the shorter the distance snow is
thrown.
ADJUSTING TRACTION DRIVE CLUTCH
1.
To adjust the chute, loosen the hand knob. See
Figure 25.
Refer to the Final Adjustments section on page 10
for instructions to adjust the traction drive clutch. If
you  are  not  sure  whether  you  have  been  able  to
adjust  the  traction  drive  clutch  properly,  check  as
follows.
2.
Pivot  the   top  of   the  chute   assembly  to   the
position desired.
1.
Drain the gasoline from the snow thrower or put
a  plastic  film  under  the  gas   cap  if  the  snow
thrower  has   already  been   operated.  Tip   the
snow thrower forward onto the auger housing.
2.
3.
Remove  the  frame  cover  underneath  the  snow
thrower by removing the six self-tapping screws.
With the traction drive clutch released, check if
there  is  clearance  between  the   friction  wheel
and  the  drive  plate  in  all  positions  of  the  shift
lever.  For  correct  adjustment  there  has  to  be
enough clearance.
Hand
Knob
4.
With the traction drive clutch engaged, check if
the  friction  wheel  is  contacting  the  drive  plate.
See Figure 26.
Figure 25  
14
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals
Tags, , , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website