MTD E662H E642E 614E E644E E664F E6A4E Snow Blower Owners Manual

Adjusting The Skid Shoes
The space between the shave plate and the ground
can be adjusted by adjusting the skid shoes.
1.
Place skid shoes in the low position to remove
snow close to the ground. Place skid shoes in a
higher  position  to  remove   snow  from  uneven
ground. See Figure 19.
Low Position
High Position
2.
Adjust skid shoes by loosening the four hex nuts
and  carriage  bolts  and  moving  skid  shoes  to
desired position. Make certain the entire bottom
surface  of  skid  shoe  is  against  the  ground  to
avoid uneven wear on the skid shoes. Retighten
nuts and bolts securely.
Skid
Shoe
Hex Nuts
Carriage Bolts
Figure 19  
WARNING: It   is    not   recommended
that  you  operate  this  snow  thrower  on
gravel  as   loose  gravel  can   be  easily
picked  up   and   thrown  by   the  auger
causing an injury and/or damage to the
snow thrower.
SECTION 6:  CONTROLS
THROTTLE CONTROL
SHIFT LEVER
The throttle control is located on the engine. It regulates
the speed of the engine. See Figure 21
(See Figure 22 for Model 642 and 662. See Figure
23 for Models 614, 644, 664, and 6A4)
The shift lever is located in the center of the handle
panel. The shift lever may be moved into one of six
positions.   Run   engine   with   throttle   in   the   fast
position.  Use  the  shift  lever   to  determine  ground
speed.
SAFETY IGNITION SWITCH
The ignition key must be inserted in the switch before
the  unit  will  start.  Remove  the  ignition  key  when
snow thrower is not in use
Forward—Five  forward  speeds:  position  one  (1)  is
the slowest; position five (5) is the fastest.
Reverse—One reverse (R) speed.
FUEL SHUT-OFF
VALVE
Closed
The  fuel   shut-off  valve,
located  under  fuel  tank,
controls   fuel   flow  from
tank. (If equipped)
NOTE:  Model 614, 644, 664, and 6A4 has seven
positions.
Open
AUGER DRIVE CLUTCH
Figure 20  
See Figure 20.
(See Figure 22 for Model 642 and 662. See Figure
23 for Models 614, 644, 664, and 6A4)
The auger drive clutch is located on the left handle.
Squeeze the auger drive clutch against the handle to
engage   the  augers.   Release   to  stop   the   snow
throwing action.
Starter
Handle
TRACTION DRIVE CLUTCH
(See Figure 22 for Model 642 and 662. See Figure
23 for Models 614, 644, 664, and 6A4)
The  traction   drive  clutch  is   located  on  the   right
handle. Squeeze the traction drive clutch to engage
the wheel drive. Release to stop.
CHUTE CRANK
Ignition
Key
(See Figure 22 for Model 642 and 662. See Figure
23 for Models 614, 644, 664, and 6A4)
The chute crank is located on left hand side of the
snow thrower.
Primer
Choke
Throttle
To  change  the  direction  in  which  snow  is  thrown,
turn chute crank as follows:
Figure 21  
Crank clockwise to discharge to the left.
Crank counterclockwise to discharge to the right.
11
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals
Tags, , , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website