MTD E662H E642E 614E E644E E664F E6A4E Snow Blower Owners Manual

SECTION 5:  ASSEMBLY INSTRUCTIONS
IMPORTANT: After assembly, service engine with
gasoline,  and  check  oil  level   as  instructed  in  the
separate engine manual packed with your unit.
Attaching the Handle Assembly.
(Hardware A and E)
Lay loose parts out on flat surface.
NOTE: All  references  to  right  or  left  side   of  the
snow thrower are determined from behind the unit in
the operating position.
1.
2.
3.
4.
Handle Panel
Right Handle
Left Handle
5.   Traction Drive Control
Grip
6.
Right Grip Bracket
UNPACKING
7.   Left Grip Bracket
Auger Control Grip
1.
Remove staples or break glue on the top flaps of
the   carton.    Remove    any   loose    parts   like
operator’s  manual   or  hardware  pack  included
with unit.
1
2.
3.
4.
5.
Cut  along  dotted  lines  and   lay  end  of  carton
down flat. Remove packing material.
Roll unit out of carton. Check carton thoroughly
for loose parts.
7
6
5
4
Extend cables out behind unit and lay them on
the floor.
Lay   out  the   contents  of   the   hardware  pack
according  to   the  illustration  in   section  4  and
identify each part.
2
3
6.
Find the loose parts in the carton and lay these
on the floor. See Figure 3. You should locate the
following loose parts in the carton:
Figure 3  
1.
Attach  left  handle  and   grip  bracket  to  handle
panel with two carriage   bolts, lock washers and
hex nuts. (Be sure the bend in the grip  bracket is
towards  the  center  of  the  handle   panel.  (See
Figure 4.) Do not tighten at this time.
1.
2.
3.
4.
5.
6.
7.
8.
Handle Panel
Right Handle
Left Handle
Auger Control Grip
Traction Drive Control Grip
Right Clutch Grip Bracket
Left Clutch Grip Bracket
Shift Rod (Not Illustrated)
Chute Crank Assembly (Not Illustrated)
Chute Assembly (Not Illustrated)
Hardware Pack (Not Illustrated)
Handle Panel
Outer
Edge
of Handle
Panel
9.
10.
11.
Left Grip Bracket
TOOLS REQUIRED
Carriage
Bolts
The  snow  thrower  comes  partly  assembled  in  the
carton.  You  will   have  to  complete   the  assembly.
Follow   assembly    instructions   in   this    operator’s
manual to make the job safe and easy. You will need
the following tools to assemble the snow thrower.
Hex Nuts
Left Handle
(curves in)
A.
B.
Set of Wrenches (3/8", 9/16", 1/2" or
adjustable)
Pair of pliers
Lock Washers
Figure 4  
2.
Locate  auger  control  grip,  part  #4  in  Figure  3.
The triangular metal tab on the auger control grip
must face the center of the handle panel.
6
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals
Tags, , , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website