Toro 05144SL Rev A Line Painter 1200 Service Manual

Paint Shutoff Valve Removal (Fig. 18)
Drain paint tank (see  Operator’s Manual). Operate
7.  Connect extension spring (item 9) to lever.
1.
8.  Connect inlet and outlet hoses to paint shutoff valve
(Fig. 19) (see Quick Disconnect Fitting in the General In-
formation section).
line painter in the flush mode to clean paint tubes.
2.
Park machine on  a level surface,  stop engine, en-
gage parking  brake and remove key  from the ignition
switch. Remove high tension lead  from the spark plug
and position the lead away from the spark plug.
9.  Install flush tank (see Flush Tank Installation in  this
section).
10.Secure
high tension lead to spark plug.
3.
Remove flush tank (see Flush Tank Removal in this
section).
4.
Remove inlet  and  outlet hoses  from paint  shutoff
valve (Fig. 19) (see Quick Disconnect Fitting in the Gen-
eral Information section).
4
1
5.
Disconnect extension spring (item 9) from lever (item
10).
6.
Remove hair pin (item 11) and pin (item 12) that se-
cure cable to lever.
2
7.
Remove two (2) cotterless pins (item 13) that retain
lever to shutoff valve (Fig. 20). Remove lever from valve.
3
8.
Remove flange nut (item 5), cap screw (item 14) and
flat washer (item  15) that secure shutoff  valve to tank
support. Remove valve from machine.
Figure 19
3.
4.
9.
If needed, remove fittings from shutoff valve.
1.
2.
Cable
Outlet hose
Inlet hose
Paint shutoff valve
10.If
required, push spool from manifold block. Remove
and discard o–rings. Thoroughly clean spool and man-
ifold block.
1
Paint Shutoff Valve Installation (Fig. 18)
1.
If spool  was  removed from  manifold block,  install
new o–rings on spool. Lightly grease o–rings and spool.
Push spool into manifold block.
2
2.
If fittings  were  removed from  shutoff valve,  apply
Saf–T–Lok  PTFE   Pipe  Sealant   (or  equivalent)   to
threads of fittings (see Thread Sealant for Paint System
Fittings in  the General Information  section). Install fit-
tings to valve. Torque fittings to values identified in Fig.
18.
Figure 20
2.
1.
Pivot cotterless pin
Spool cotterless pin
4
3
3.
(item 14), flat washer (item 15) and flange nut (item 5).
Do not fully tighten nut.
Position valve to tank support and install cap screw
5
4.
Position lever to valve and install two (2)  cotterless
pins (item 13) to secure lever to shutoff valve.
5.
(item 11).
Secure cable to lever with pin (item 12) and hair pin
1
2
Figure 21
4.
5.
6.
machine.
Tighten flange nut (item 5) to secure shutoff valve to
1.
2.
3.
Manifold block
Spool
O–ring
O–ring
O–ring
Line Painter 1200
Page 5 – 21 (Rev. A)
Paint System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 92 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website