Toro 05144SL Rev A Line Painter 1200 Service Manual

NOTE:  Individual components for  the ball  valves are
not available.
10.Install flush tank (see Flush (Water) Tank Installation
in this section).
NOTE:  Ball valve nut threads have thread sealant ap-
plied during initial assembly. Nut removal may  be diffi-
cult.
11.Secure high tension lead to spark plug.
1
10.If
needed, disassemble ball valve using Fig. 27 as a
guide.
3
Installation (Fig. 25)
1.
If  ball  valves  were  disassembled,  assemble  ball
valves using Fig. 27 as a guide. Torque nut 45 to 55 in–lb
to 6.2 N–m).
(5.1
NOTE:  When assembling ball valves and lever to ball
valve bracket, make sure that valve ball is orientated to
upper fitting opening of ball valve assembly and lever is
in the paint (lowered) position.
2
Figure 26
2.
Position ball valves and lever to ball valve bracket.
1.
2.
To spray pump
To pressure regulator
3.
Lever (paint position)
IMPORTANT: Install fittings into ball valves by hand
to prevent cross–threading the ball valve threads.
7
45
to 55 in–lb
9
3.
Apply Saf–T–Lok PTFE Pipe Sealant (or equivalent)
(5.1
to 6.2 N–m)
to threads of all removed fittings (see Thread Sealant for
Paint System  Fittings in the General  Information sec-
tion). Install fittings to ball valves as follows:
4
6
4
2
A.  Tighten recirculation port (item 24) so that clear-
ance between port neck  and top of bracket is from
1
0.000”
(flush) to .030” (.0 to .8 mm) (Fig. 28).
8
B.  Tighten outlet port (item 7) so that clearance be-
tween bottom of hex and top of bracket is from 0.000”
(flush) to .030” (.0 to .8 mm) (Fig. 28).
5
3
C. Torque remaining fittings to value identified in Fig.
25.
Figure 27
1.
2.
3.
4.
5.
Nut
6.
7.
8.
9.
Valve ball
Spindle
4.
ports. Position ball valve assembly to machine.
Place new  rubber  washers (item  6) on  ball  valve
Cover
O–ring
O–ring
Seat
Housing
O–ring (2 used)
5.
Install two (2) flange screws (item 16) that secure ball
valve assembly to tank support but do not fully tighten.
0.000”
to .030”
6.
elbow fitting  (item 3)  that secure  ball valve  fittings to
paint tank. Tighten jam  nuts. Torque elbow fitting from
Install washers (items 4 and 5), jam nuts (item 2) and
(0.0 to .8 mm)
1
2
144
to 156 in–lb (16.3 to 17.6 N–m).
7.
Tighten two (2) flange screws (item 16).
8.
Install hoses to fittings on ball valves (Fig. 26)  (see
Quick Disconnect Fitting in the General Information sec-
tion).
9.
Install knob (item 19) to lever.
Figure 28
1.
Recirculation port
2.   Outlet port
Line Painter 1200
Page 5 – 25 (Rev. A)
Paint System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 92 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website