Yard Machines E602E E642EE642F E662E E662H 614E E644E E664F E6A4E Snow Blower Owners Manual by MTD

6.
Check  to  make  sure  all  nuts  and  bolts   on  the
control panel and all four bolts    which  secure the
handles to the frame are tight.
3.   Now  release  the  traction  control  clutch  grip,  and
push the unit again. Move the shift lever back to
the fast reverse position, then all the way forward
again. There should be no resistance in the shift
lever, and the wheels should keep turning.
LAMP WIRING (If Equipped)
4.
If you have resistance when moving the shift lever
or the wheels stop when they should not, loosen
the  jam   nut  on  the   traction  control  cable   and
unthread the cable  one turn.  If the wheels do not
stop when you engage the traction control clutch
grip,  loosen  the  jam  nut  on  the  traction  control
cable and thread the cable in one turn. Recheck
the adjustment and repeat as necessary.
Lamp Wire  Alternator
Lead
Right Handle
5.
Tighten  the  jam  nut  to  secure  the   cable  when
correct adjustment is reached.
Figure 17  
1.
Wrap  the   wire  from   the  lamp   down  the   right
handle  until  the   wire  can  be   plugged  into  the
alternator    lead   wire  under  the  fuel  tank.   See
Figure  17.  Be  sure  lamp  wire  does  not  interfere
with the movement of any controls or cables.
NOTE: If  you  are  uncertain  that  you  have  reached
the    correct    adjustment,   refer    to    SECTION    8:
ADJUSTMENTS.
Adjusting The Skid Shoes
IMPORTANT:   After   attaching  the  shift   rod  and
clutch  cables,  check  the  adjustments  as  instructed,
and  make  any   final  adjustments  necessary   before
operating  your  snow  thrower.   Failure  to  follow  the
instructions may cause damage to the snow thrower.
The  space  between  the  shave  plate  and  the  ground
can be adjusted by adjusting the skid shoes.
1.
Place  skid  shoes  in  the  low  position  to  remove
snow close to the ground. Place skid shoes in a
higher   position  to   remove  snow   from   uneven
ground. See Figure 18.
FINAL ADJUSTMENTS
Auger Control Clutch
2.
Adjust skid shoes by loosening the four hex nuts
and  carriage   bolts  and   moving  skid   shoes  to
desired  position.  Make  certain  the  entire  bottom
surface of skid shoe is against the ground to avoid
uneven  wear  on  the  skid  shoes.  Retighten  nuts
and bolts securely.
1.
2.
3.
To  check   the  adjustment  of   the  auger  control
clutch,  push  forward  on  the  left  hand  clutch  grip
depressing  the  rubber  bumper  under  the  clutch
grip. There should be slack in the cable.
Release  the   clutch  grip.  The   cable  should  be
straight. Make certain you can   depress the  auger
control    clutch   grip    against    the   left    handle
completely.
If  necessary,  loosen  the hex jam  nut  and thread
the cable in (for less slack) or out (for more slack)
as  necessary.  Refer  to  Figure  12.  Recheck  the
adjustment. Tighten the jam nut against the cable
when correct adjustment is reached.
Skid
Shoe
Low Position
High Position
Hex Nuts
Carriage
Bolts
Figure 18  
Traction Control Clutch and Shift Lever
Adjustment
WARNING: It is not recommended that
you operate this snow thrower on gravel
as  loose  gravel  can  be  easily  picked  up
and   thrown  by   the   auger  causing   an
injury    and/or    damage    to    the   snow
thrower.
To check the adjustment of the traction control clutch
and shift lever:
1.
Move  the  shift  lever  all  the  way  to  the  highest
speed.  With  the  traction  control  lever  released,
push  the  snow  thrower  forward.  The  unit  should
roll forward.
2.
Then engage the traction control clutch grip. The
wheels should stop turning.
10
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals, Yard Machines Snow Blower Manuals
Tags, , , , , , , , , , , , , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandYard Machines, 614E, E602E, E642EE642F, E644E, E662E, E662H, E664F, E6A4E, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website