Yard Machines E602E E642EE642F E662E E662H 614E E644E E664F E6A4E Snow Blower Owners Manual by MTD

Flat
Washer
Lock
Washers
Shift
Hairpin
Lever
Clip
Cable
Roller
Guide
Hex Bolt
Ferrule
Handle
3/4”
Long
Tab
Shift
Rod
Hex
Bolt 1-3/4”
Long
Flat
Washer
Figure 9  
Hairpin
Shift
Clip
Arm
ATTACHING SHIFT ROD
(Hardware D)
Assembly
Models 614, 644, 664, and 6A4
1.
Place the shift lever in the fastest forward speed
position.
Figure 11  
3.
Models 602, 642, 662:   Thread the ferrule up or
down the shift rod and align with the lower hole on
the shift lever assembly behind the handle panel.
See Figure 10 .
Models  614,  644,  664,  and  6A4:   Thread  the
ferrule onto the shift rod, up or down the shift rod
and align with the far hole on the narrow side of the
shift lever assembly behind the handle panel. See
Figure 11.
2.
Models  602,  642,   662:  Rotate  the   shift  arm
assembly counter clockwise, as far as it will go.
Insert   the   shift   rod   through    the   shift   arm
assembly. When installed the shift arm assembly
should point to the right. Secure with flat washer
and hairpin clip. See Figure 10.
Models 614, 644, 664 and 6A4: Rotate the shift
arm assembly counter clockwise as far as it will
go.  Insert  the  shift  rod   through  the  shift  arm
assembly.    When    installed,    the    shift    arm
assembly   should  point   left.   Secure  with   flat
washer and hairpin clip. See Figure 11.
4.
Secure the ferrule to the shift arm assembly with
flat washer and hairpin clip.
NOTE: Make     certain    to     check    for     correct
adjustment of the shift rod as instructed in the FINAL
ADJUSTMENTS section before operating the snow
thrower.
Traction
Shift
Drive
Lever
Clutch
ATTACHING CLUTCH CABLES
(Hardware D)
Ferrule
(Bottom
Hole)
1.
Thread  the  hex  jam  nuts  all   the  way  up  the
threaded portion of the “Z” ends.
Flat
Washer
2.
Make certain all cables are in the grooves of the
cable roller guides. The roller guides are located
in the lower rear of the unit. Lift the clutch grip in
the raised (up) position.
Hairpin
Clip
Shift
Rod
3.
Thread  the  cable  onto  the  threaded  portion  of
the “Z” end until there is no slack in the cable,
but  the  cable  is  NOT  tight.  Do  not  overtighten
cable. See Figure 12.
Flat
Washer
Hairpin
Clip
Shift
Arm
Assembly
WARNING: If   cable  is   tightened   so
there  is  tension  on  the  cable  with  the
clutch grip released, the safety features
of the snow thrower may be overridden.
Models 602, 642 and 662
Figure 10  
8
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals, Yard Machines Snow Blower Manuals
Tags, , , , , , , , , , , , , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandYard Machines, 614E, E602E, E642EE642F, E644E, E662E, E662H, E664F, E6A4E, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website