Yard Machines E602E E642EE642F E662E E662H 614E E644E E664F E6A4E Snow Blower Owners Manual by MTD

Rear
Auger
Belt
Drive
Belt
Friction
Wheel
Engine
Pulley
Front
Auger
Belt
Support
Bracket
Engine
Pulley
Frame
Idler
Pulley
Idler
Pulley
Rear
Auger
Belt
Figure 29  
NOTE: It may be necessary to loosen the six hex
nuts  that  fasten  the  frame  to  the  auger  housing  to
aid in belt removal.
Front
Auger
Pulley
Support
Bracket
Spring
Auger
Pulley
Idler
Auger
Housing
Spring
5.
6.
7.
Roll the front and rear auger belts off the engine
pulley. See Figure 29.
Figure 30  
Unhook the idler spring from the hex bolt on the
auger housing. See Figure 30.
Friction
Wheel
Disc
Back out the stop bolt to allow the belts to slip
between the bolt and auger pulley.
See Figure 31.
Friction Wheel
Drive Belt
8.
9.
Lift  the  rear  auger  belt  from  the  auger  pulley,
and  slip  belt  between  the  support  bracket  and
the  auger  pulley.  See  Figure  31.  Repeat  this
step for front auger belt.
Support Bracket
Replace  both  auger  control  belts  by  following
instructions in reverse order.
Stop
Bolt
DRIVE BELT
1.
Follow    steps     1    through    4     of    previous
instructions.
Figure 31  
2.
Pull idler pulley up, and lift belt off engine pulley,
idler pulley, and friction wheel disc.
See Figure 29.
CHANGING THE FRICTION WHEEL
RUBBER
3.
4.
Back out the stop bolt until the support bracket
rests on the auger pulley. See Figure 31.
The rubber on the friction wheel is subject to wear
and should be checked after 25 hours of operation,
and   periodically   thereafter.   Replace   the   friction
wheel  rubber  if  any  signs  of  wear  or  cracking  are
found.
Slip   belt  between   friction  wheel   and   friction
wheel disc. See Figure 31. Remove and replace
belt.  Reassemble  following   the  instructions  in
reverse order.
1.
2.
3.
4.
Drain  the  gasoline  from  the  snow  thrower,  or
place a piece of plastic under the gas cap.
NOTE: The support bracket must rest on the stop
bolt  after  the  new  belt  has  been  assembled.  See
Figure 31.
Tip the snow thrower up and forward, so that it
rests on the auger housing.
Remove six self-tapping screws from the frame
cover underneath the snow thrower.
Remove the klick pins which secure the wheels,
and remove the wheels from the axle.
17
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals, Yard Machines Snow Blower Manuals
Tags, , , , , , , , , , , , , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandYard Machines, 614E, E602E, E642EE642F, E644E, E662E, E662H, E664F, E6A4E, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website