Yard Machines E602E E642EE642F E662E E662H 614E E644E E664F E6A4E Snow Blower Owners Manual by MTD

Set the skid shoes 1/4" below the scraper bar
for  normal  usage.  The   skid  shoes  may  be
adjusted upward for hard-packed snow. Adjust
downward  when  using  on  gravel  or  crushed
rock.
•  Be   certain  to   follow  the   precautions  listed
under ‘‘To Stop Engine’’ in previous column to
prevent possible freeze-up.
Clean the snow thrower thoroughly after each
use.
SECTION 8:  ADJUSTMENTS
WARNING: Never   attempt    to   clean
chute  or  make  any  adjustments  while
engine is running.
2.   Remove  the  frame  cover  underneath  the  snow
thrower by removing the six self-tapping screws.
3.
With the traction control clutch released, check if
there  is  clearance  between  the   friction  wheel
and  the  drive  plate  in  all  positions  of  the  shift
lever.  For  correct  adjustment  there  has  to  be
enough clearance.
ADJUSTING CHUTE
You can control the distance that snow is thrown by
adjusting  the   angle  of   the  chute  assembly.   The
sharper the angle, the shorter the distance snow is
thrown.
4.   With the traction control clutch engaged, check if
the  friction  wheel  is  contacting  the  drive  plate.
See Figure 25.
1.
To adjust the chute, loosen the hand knob. See
Figure 24.
5.   If  adjustment  is  necessary,  loosen  the  jam  nut
on the traction control cable, and thread cable in
or out as necessary.
2.
Pivot  the   top  of   the  chute   assembly  to   the
position desired.
6.
Tighten  the  jam  nut  to  secure  the  cable  when
correct adjustment is reached. Reassemble the
frame cover with six self-tapping screws.
Friction
Wheel
Hand
Knob
Gear
Shaft
Figure 24  
ADJUSTING SKID SHOE
Drive
Plate
The space between the shave plate and the ground
can be adjusted by adjusting the skid shoe. Slide the
skid shoe upwards and lower the housing to remove
snow   close    to    the   ground.    Slide   skid    shoe
downwards  and  raise  the  housing  to  remove  snow
from  uneven  ground  like  gravel.  For  more  details,
refer to Adjusting the Skid Shoes in section 5.
Figure 25  
Note: If  you  had  earlier  placed  plastic  film  under
the   gas   cap,   be  sure   to   remove   it   once   the
adjustment to the traction control clutch is done and
the snow thrower frame is re-installed.
ADJUSTING TRACTION CONTROL
CLUTCH
Refer  to the Final Adjustments section on page 10
for instructions to adjust the traction control clutch. If
you  are  not  sure  whether  you  have  been  able  to
adjust the traction control clutch properly, check as
follows.
ADJUSTING AUGER CLUTCH
To   adjust   the  auger   clutch,   refer   to   the   Final
Adjustments in section 5.
1.
Drain the gasoline from the snow thrower or put
a  plastic  film  under  the  gas   cap  if  the  snow
thrower  has   already  been   operated.  Tip   the
snow thrower forward onto the auger housing.
14
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals, Yard Machines Snow Blower Manuals
Tags, , , , , , , , , , , , , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandYard Machines, 614E, E602E, E642EE642F, E644E, E662E, E662H, E664F, E6A4E, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website