A. Grasp the recoil starter handle (Fig. 17) and pull it
out slowly until positive engagement results; then
pull the handle vigorously to start the engine.
Auger/Impeller Drive Belt on page 20. If the problem
persists, take the snowthrower to an Authorized Service
Dealer for service.
B. Keep a firm grip on the starter handle and return the
rope slowly.
For the electric starter:
A. Connect the power cord to the snowthrower
(Fig. 18) and to a standard household power outlet.
Caution
m-2680
1
If you leave the snowthrower plugged into a power
outlet, someone can inadvertently start the
snowthrower and injure people or damage
property.
Figure 21
1.
Large screw head
Unplug the power cord whenever you do are not
starting the snowthrower.
Stopping the Engine
1.
Engage the auger to clear any remaining snow from
inside the housing.
B. Push the starter button.
Note: Run the electric starter no more than ten times at
intervals of five seconds on, then five seconds off.
2.
Run the engine for a few minutes to dry off any
accumulated moisture.
Important
Running the electric starter extensively can
3. Release the auger/impeller drive control lever and the
overheat and damage the starter.
traction control lever (Fig. 13).
Note: If the engine does not start after this series of
attempts, wait at least 40 minutes to allow the starter to
cool before attempting to start it again.
4. Shift the traction drive into the N (Neutral) position.
5.
Stop the engine by doing one of the following:
A. Move the throttle to the Slow position and remove
the ignition key.
Note: If the engine does not start after the second series
of attempts, take the snowthrower to an Authorized
Service Dealer for service.
B. Move the throttle to the Stop position.
C. When the engine starts, disconnect the power cord
from the snowthrower and the outlet.
6.
7.
Close the fuel shutoff valve (Fig. 15).
Pull the recoil starter with a rapid, continuous, full-arm
stroke three or four times. This prevents the recoil
starter from freezing up.
Note:–10_ If engine_
does not start or if the air temperature is
F (–23 C) or colder, the engine may need additional
priming. After pushing in the primer, try to start the engine
before priming again.
8. Wait for all moving parts to stop before leaving the
operating position.
9.
After the engine starts, immediately rotate the choke
(Fig. 14) to the 3/4 position. As the engine warms up,
rotate the choke to the 1/2 position. When the engine
warms up sufficiently, rotate the choke to the Off
position.
Operating the Power Shift
Feature
Move the wheels to the rear Power Shift position in heavy
or drifted snow. Leave the wheels in the front position for
light snow or for transporting the snowthrower.
Important
Ensure that the auger and impeller do not
rotate while the auger/impeller drive control lever is in the
Disengaged position. Stand in the operating position and
look around to the side of the auger housing (Fig. 21). A
large screw head on the side of the auger housing rotates
when the auger and impeller rotate (Fig. 21). If the auger
and impeller rotate while the engine runs and the
With the engine running at full speed:
1. Release the traction control lever (Fig. 13).
2.
Move the speed shift control fully forward to the Power
Shift position and hold it there (Fig. 22).
auger/impeller drive control lever is disengaged, stop the
snowthrower immediately. Refer to Adjusting the
15
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 1028 Power Shift, Toro 1332 Power Shift, Toro 38547, Toro 38560, Toro 38592, Toro 924 Power Shift |
| Model Number | 38547, 38560 and 38592 |
| Model Year | 2002 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 220000001 - 220999999 |
| Product Name | Toro 924 Power Shift Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Two Stage Power Shift |
| Swath | 24 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 26 oz. (.8l) 5w-30 or 10w / API SH or higher |
| Engine Motor Model # | OHSK90-221413C |
| Engine Motor Size | 9 hp |
| Engine Motor Type | 4 Cycle CARB1, EPA1 |
| Transmission Speed | 4 Forward/2 Reverse |
| Transmission Type | Gear |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)