3.
Remove the three flange-head bolts that secure the belt
cover to the engine frame and slide the belt cover and
the cable cover up the cables (Fig. 5).
1. Stop the engine and wait for all moving parts to stop.
2.
Disconnect the wire from the spark plug and ensure that
the wire does not contact the plug (Fig. 32).
4.
5.
Move the speed shift control to the N (Neutral) position.
1
Remove the two-flange bolts that secure the idler pulley
assembly to the engine frame and remove idler pulley
assembly (Fig. 31).
6.
7.
8.
Remove the bolt and the lock washer that secure the
half sheave to the front of the pulley assembly (Fig. 31).
Slide the half sheave and auger/impeller drive belt off
the crankshaft and remove the belt (Fig. 31).
m-4068
Figure 32
If you need to replace the traction drive belt, slide the
middle pulley section and the belt off the crankshaft,
and remove the belt from the pulley (Fig. 31).
1.
Spark plug wire
3.
Clean the area around the oil drain plug (Fig. 33).
9.
On the control cable that corresponds to the belt you are
replacing, loosen the jam nuts that secure the cable to
the bracket (Fig. 28).
Note: The cable must slide freely in the bracket when
you change the belts.
10.
If you replace the traction drive belt, install it around
the traction drive and the middle pulley section, and
slide the middle pulley section onto the crankshaft
(Fig. 31).
1
182
Figure 33
1.
Drain plug
11.
12.
Install the traction drive belt on the idler pulley
(Fig. 31).
4.
Slide an oil drain pan under the drain extension and
remove the oil drain plug.
Install the auger/impeller drive belt around the half
sheave, and slide the half sheave onto the crankshaft
(Fig. 31).
5.
6.
7.
Drain the oil.
Note: Ensure that the tabs on the half sheave are
inserted into the mounting grooves in the middle pulley.
Install the oil drain plug.
Fill the crankcase with oil. Refer to Filling the Engine
Crankcase with Oil on page 11.
13.
14.
Install the bolt and the lock washer that secure the half
sheave to the front of the pulley assembly.
8.
9.
Wipe up any spilled oil.
Install the idler pulley assembly on the engine frame
and secure it with the two flange-head bolts (Fig. 31).
Connect the wire to the spark plug.
Note: Ensure that the idler pulleys align with the belts
when you install the idler pulley assembly.
15.
16.
Install the belt and the cable covers.
To adjust the belts, refer to Adjusting the Traction Drive
Belt on page 20 or Adjusting the Auger/Impeller Drive
Belt on page 20.
17.
Connect the wire to the spark plug.
Changing the Engine Oil
Change the engine oil after the first two operating hours,
after every 25 operating hours, and at the end of the
snowthrowing season. If possible, run the engine just
before changing the oil because warm oil flows better and
carries more contaminants.
22
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 1028 Power Shift, Toro 1332 Power Shift, Toro 38547, Toro 38560, Toro 38592, Toro 924 Power Shift |
| Model Number | 38547, 38560 and 38592 |
| Model Year | 2002 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 220000001 - 220999999 |
| Product Name | Toro 924 Power Shift Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Two Stage Power Shift |
| Swath | 24 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 26 oz. (.8l) 5w-30 or 10w / API SH or higher |
| Engine Motor Model # | OHSK90-221413C |
| Engine Motor Size | 9 hp |
| Engine Motor Type | 4 Cycle CARB1, EPA1 |
| Transmission Speed | 4 Forward/2 Reverse |
| Transmission Type | Gear |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)