StartingandStoppingthe
1.
2.
Clean around fuel tank cap and remove cap from
tank (Figure 15 ). Using unleaded gasoline, fill fuel Engine
tank no higher than to bottom of filter screen. Do
not overfill.
Note: For illustrations and descriptions of the
controls referenced in this section, refer to Controls,
page 13.
Install fuel tank cap and wipe up any spilled
gasoline.
StartingtheEngine
Checking the Interlock
SwitchOperation
Note: Make sure spark plug wire is installed on spark
plug.
1.
Make sure traction and reel drive levers are in
Disengaged position.
If safety interlock switches are disconnected
or damaged the machine could operate
unexpectedly causing personal injury.
Note: Engine will not start if traction lever is in
the engaged position.
2.
3.
4.
5.
Open the fuel shut-off valve on the engine.
Move the on/off switch to the On position.
Move the throttle control to the Fast position.
•
•
Do not tamper with the interlock switches.
Check the operation of the interlock switches
daily and replace any damaged switches
before operating the machine.
Move the choke lever to the half-open position
when starting a cold engine. The choke may not be
required when starting a warm engine.
•
Replace switches every two years regardless
of whether they are operating properly or not.
6.
Pull the recoil starter handle out until positive
engagement results, then pull it vigorously to start
the engine. Open the choke as engine warms up.
1.
Push kick stand down with foot and pull up on
handle support until kick stand has rotated forward,
over center (Figure 16 ).
Important: Do not pull recoil rope to its
limit or let go of starter handle when rope is
pulled out because rope may break or recoil
assembly may be damaged.
StoppingtheEngine
1.
2.
3.
Move the traction and reel drive controls to the
Disengaged position, the throttle control to Slow,
and the on/off switch to Off.
Pull the spark plug wire off of the spark plug to
prevent the possibility of accidental starting before
storing machine.
Figure16
Close the fuel shut-off valve before storing or
transporting mower in a vehicle.
1.
Kickstand
2.
Place traction lever into Engage position and
engine controls in starting position.
TransportOperation
1.
Push kick stand down with foot and pull up on
handle support until kick stand has rotated forward,
over center.
3.
Attempt to start engine. Engine should not start.
If engine starts, the interlock switch needs service.
Correct problem before operating. Refer to
Servicing Interlock Switch, page .
2.
3.
To release kickstand, pull up on handle and lower
rear of mower onto transport wheels.
4.
Carefully lift up on handle to release kick stand.
Ensure traction and reel drive controls are in
Disengage position and start engine.
16
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro 04021, Toro 04200, Toro Greensmaster |
| Model Number | 04021, 04200 |
| Model Year | 2005 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | Nederlands, English, ελληνικά, Português, Svenska |
| Product Name | Toro Greensmaster Flex 21 |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Product Series | Toro Greensmaster - Flex Series |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)