STARTING AND SHUT OFF
Electric Start
1.
Connect extension cord to prongs on
starter.
WARNING: FAILURE TO FOLLOW
INSTRUCTIONS could result in
personal injury and/or damage to
unit. DO NOT attempt to start your
unit at this time. Read entire
Owner/Operator Manual and the
Engine Manual first.
IMPORTANT: Prevent damage to unit. Know
voltage of your starter and only use matching
outlets.
2. Plug extension into 120V 3-wire,
grounded outlet.
3.
4.
Turn discharge chute straight ahead.
Make sure that the traction clutch and
attachment drive clutch levers are fully
disengaged.
IMPORTANT: Allow unit and engine to adjust
to the outdoor temperatures before clearing
snow. Before shut-off, run the attachment a
few minutes to prevent freeze-up.
NOTE: Try out each control without the engine
running to see how it works and what it does.
5.
Push Primer Bulb 2 or 3 times for cold
engine.
NOTE: When temperature is below -15° F
(-26° C) additional priming may be needed.
Manual Start
1.
2.
Turn discharge chute straight ahead.
6. Insert key into ignition switch on engine
and push into "Run" position. DO NOT
twist key after it is inserted.
Make sure that the traction clutch and
attachment drive clutch levers are fully
disengaged.
7. If engine is cold, apply choke. A warm
engine requires less choking than a cold
engine. See Engine Manual for detailed
instructions.
3.
Push Primer Bulb 2 or 3 times for cold
engine.
NOTE: When temperature is below -15° F
(-26° C) additional priming may be needed.
8.
Set throttle to proper starting position.
4.
If engine is cold, apply choke. See Engine
Manual for detailed instructions.
9. Press starter button on engine until
engine starts.
NOTE: A warm engine requires less choking
IMPORTANT: DO NOT operate starter more
than 15 seconds per minute, as overheating
and damage can occur. (If engine does not
start, refer to Troubleshooting.)
than a cold engine.
5.
6.
Set throttle to proper starting position.
Insert key into ignition switch.
10.
11.
Adjust choke as needed.
12V - Turn key into RUN position.
Disconnect power cord from outlet, then
starter.
120V - Push key into RUN position. DO
NOT twist key after it is inserted.
12.
Set throttle to Part Throttle or Slow
position for travel or adaptation to outside
temperature. Once achieved, set throttle
to Fast position for normal operation.
7.
8.
Grasp starter handle and pull rope out
slowly until it pulls harder. Let rope rewind
slowly.
Pull rope with a rapid continuous full arm
stroke. Let rope rewind slowly.
Electric Start (12V)
1.
2.
Turn discharge chute straight ahead.
Make sure that the traction clutch and
attachment drive clutch levers are fully
disengaged.
IMPORTANT: DO NOT let Starter Handle
snap against Starter.
9.
Repeat steps 7 and 8 until engine starts.
(If engine does not start, refer to
Troubleshooting.)
3. Push Primer Bulb 2 or 3 times for cold
engine.
10.
11.
Adjust choke as needed.
NOTE: When temperature is below -15° F
(-26° C) additional priming may be needed.
Set throttle to Part Throttle or Slow
position for adaptation to outside
temperature or travel. Set throttle to Fast
position for normal operation.
4.
If engine is cold, apply choke. See Engine
Manual for detailed instructions.
NOTE: A warm engine requires less choking
than a cold engine.
5.
6.
Set throttle to proper starting position.
Put ignition key into START position until
engine starts and release into the RUN
position.
GB - 18
| Categories | Ariens Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Ariens 1124, Ariens 1128, Ariens 1332, Ariens 1336, Ariens 8524, Ariens 924118, Ariens 924121, Ariens 924122, Ariens 924332, Ariens 924505, Ariens 924506, Ariens 924508, Ariens 924551 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Ariens, Snow Blower |
| Document File Type | |
| Publisher | ariens.com |
| Wikipedia's Page | Ariens |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)