STIHL FC 56C Edger Owners Manual

English
Before Starting
Warning!
Warning!
Warning!
Check for fuel leakage while refueling
and during operation. If fuel leakage is
found, do not start or run the engine until
the leak is fixed and any spilled fuel has
been wiped away. Take care not to get
fuel on your clothing. If this happens,
change your clothing immediately.
Check that the spark plug boot is
securely mounted on the spark plug – a
loose boot may cause arcing that could
ignite combustible fumes and cause a
fire.
Always check your power tool for proper
condition and operation before starting,
particularly the throttle trigger, throttle
trigger interlock, momentary stop
switch, cutting attachment, deflector
and harness. The throttle trigger must
move freely and always spring back to
the idle position. Never attempt to mod-
ify the controls or safety devices. Never
use a power tool that is damaged or not
properly maintained.
Warning!
Cap with grip
To reduce the risk
of personal injury
to the operator
from blade con-
tact and thrown
Warning!
In order to reduce the risk of fuel spill-
age and fire from an improperly
tightened fuel cap, correctly position
and tighten the fuel cap in the fuel tank
opening.
objects, make
Warning!
sure your unit is equipped with the
proper deflector, handle and harness.
Do not attach any cutting attachment to
a unit without proper installation of all
required parts. Failure to use the proper
parts may cause the blade to fly off and
seriously injure the operator or
bystanders.
To do this with this STIHL
cap, raise the grip on the
top of the cap until it is
upright at a 90° angle.
Insert the cap in the fuel
tank opening with the tri-
angular marks on the grip
of the cap and on the fuel
tank opening lining up.
Using the grip, turn the
cap firmly clockwise as
far as it will go (approx. a
quarter turn).
Warning!
The cutting attachment must be prop-
erly tightened and in safe operating
condition. Inspect for loose parts (nuts,
screws, etc.) and for cracked, bent,
warped or damaged blades. Replace
damaged blades before using the power
tool.
Always check your edger for proper
condition and operation before starting,
particularly the throttle trigger, throttle
trigger interlock (and if applicable,
momentary stop switch, cutting
attachment, deflector and harness). An
arrow on the deflector shows the correct
direction of rotation of the cutting blade.
Fold the grip flush with
the top of the cap. If the
grip does not lie com-
pletely flush with the cap
and the detent on the grip
does not fit in the corre-
sponding recess in the
filler neck, the cap is not
properly seated and tight-
ened and you must
Keep the handles clean and dry at all
times; it is particularly important to keep
them free of moisture, pitch, oil, grease
or resin in order for you to maintain a firm
grip and properly control your power
tool.
The arrow on the deflector must always
face away from you, so that cuttings and
other debris will be diverted away from
the machine and your position (see
chapter "Working Techniques").
repeat the above steps.
6
FC 56 C
Product Specification
CategoriesSTIHL Straight Edger Manuals, Straight Edger Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 80 pages
LanguageEnglish, Español
Product BrandSTIHL. Stihl Inc, USA - Corporate phone: (757) 486-9100. International Support Information: http://stihl.com Email: info@stihl.com, Edger
Document File TypePDF
Publisherstihl.com
Wikipedia's PageStihl
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website