ENGINE REMOVAL AND INSTALLATION
1965
- 1985 MODELS, ENGINE REMOVAL
Chain Drive Units:
A. Remove the left side plate, chain guard and
chain. To remove the chain, refer to "Chain
Replacement" on page 5 - 25. Consult step 2.
Certain engine servicing procedures will require
removing the engine from your snowthrower. The
following procedures are required for engine removal:
B. Remove the crankshaft sprocket. Refer to
"Crankshaft Sprocket Replacement (all
models)" on page 5 - 21. Consult step 3.
1.
2.
Drain the gasoline from the fuel tank. Refer to
“Draining The Fuel Tank” on page 2 - 5.
6.
Remove the switch terminal from the key switch if
your unit is so equipped. Some 1980 model
S-200’s may have a terminal connection slightly
below the key switch. It will be necessary to
separate the two terminals.
Remove all the mounting screws retaining the
upper shroud on 20” units. On all 14” and 21”
snowthrowers, remove both the upper and lower
shrouds. Be certain to install the gas cap after the
upper shroud is removed.
7.
8.
Slide the primer hose off the primer bulb fitting.
3.
4.
Disconnect the spark plug wire.
Remove the choke control. Note: Do not bend or
misform the carburetor choke control linkage.
Pull the rope from the starter and tie a small knot
in the starter rope before the starter housing
(Figure 34). Allow the starter rope to retract until
the knot stops the starter rope at the starter
housing. Next, remove the knot in the starter
handle and slide the handle off the starter rope.
9.
Remove the mounting screws retaining the lower
shroud on all 20” units. On electric start 20” units,
remove screws retaining the switch and plug
assembly to the lower shroud.
10.
Using a hose clamp pliers or a needle nose pliers,
compress the fuel line clamp at the carburetor
fitting and slide the clamp down the fuel line hose
(Figure 35). Remove the fuel line from the
carburetor.
Figure 34
0217-017
5.
Belt Drive Units:
A. Remove the left side plate and belt. Refer to
"Replacing Drive Belt" on page 5 - 1.
Complete steps 1 through 4.
Figure 35
0217-018
B. Remove the crankshaft pulley. Refer to
"Replacing Drive Belt" on page 5 - 1.
Complete step 2.
Single Stage Snowthrower Service Manual
4 - 1
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 1028 Power Shift, Toro 1332 Power Shift, Toro 38014, Toro 38030, Toro 38079, Toro 38087, Toro 38400, Toro 38405, Toro 38513, Toro 38543, Toro 38558, Toro 38559, Toro 38574, Toro 624, Toro 824, Toro 828, Toro 924, Toro CCR 1000 |
| Model Year | 1978, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003 |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Serial Number | 200000001 - 200999999 |
| Product Name | Toro CCR 1000 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | CCR 1000/2400/2500, Single Stage, Snowthrower |
| Swath | 20 inch |
| Discharge | Single Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Engine Motor Model # | HSK635-1721A |
| Engine Motor Size | 3.5 hp |
| Engine Motor Type | 2 Cycle EPA1 |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)