TROUBLESHOOTING
CCR2000 With The 47P Series Engine
The main jet in this carburetor (Figure 186) is in the
center hub or boss. It can be removed with a flat blade
screwdriver. Spray the seat area where the needle was
and the center where the jet was with carburetor
cleaner, allow to drain.
This is a fixed jet carburetor so there is no adjustment
needle to remove. However, some cleaning can be
done without removing the lower shroud. Again drain
the old fuel using a pump type siphon. If possible, put
the machine on a workbench. Right below the choke
control is a cut out in the lower shroud (Figure 184).
A
A
Figure 186
1352-11
(A) Main Jet
Figure 184
1352-16
Clean the jet. The best way to do that is to pass
something through the hole in the jet. A strand of
copper wire is good for this. Do not use something that
would enlarge the hole. Reassemble the carburetor,
add fresh fuel, and try to start the engine. As before, if
it starts, allow it to run for at least 10 minutes. If fuel
still cannot pass through the carburetor, it will be
necessary to remove the carburetor to fully clean and
rebuild.
(A) Bowl Nut
This is to access the carburetor bowl. Remove the
bowl nut and be prepared to catch any fuel that is in the
carburetor bowl and fuel line.
The float hinge can be removed with a needle nose
pliers and the float and needle removed (Figure 185).
Note: There is a very fine spring attached to the float
hinge.
CCR’s With R tek Engines
Drain the fuel tank with a pump type siphon.
To access the carburetor, it will be necessary to
remove the lower shroud. Refer to the "ENGINE
REMOVAL AND INSTALLATION" section for the
necessary steps.
With the machine setting upright, remove the
carburetor bowl and catch any fuel from the bowl or
fuel line.
A
Figure 185
1352-10
(A) Float Hinge
8 - 2
Single Stage Snowthrower Service Manual
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 1028 Power Shift, Toro 1332 Power Shift, Toro 38014, Toro 38030, Toro 38079, Toro 38087, Toro 38400, Toro 38405, Toro 38513, Toro 38543, Toro 38558, Toro 38559, Toro 38574, Toro 624, Toro 824, Toro 828, Toro 924, Toro CCR 1000 |
| Model Year | 1978, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003 |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Serial Number | 200000001 - 200999999 |
| Product Name | Toro CCR 1000 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | CCR 1000/2400/2500, Single Stage, Snowthrower |
| Swath | 20 inch |
| Discharge | Single Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Engine Motor Model # | HSK635-1721A |
| Engine Motor Size | 3.5 hp |
| Engine Motor Type | 2 Cycle EPA1 |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)