Toro Power Max and Snow Commander CCR 2400, 2450, 3000, 3650 Snow Blower Engine Service Manual, 1999-2007

FUEL SYSTEM
Operation
Fuel Cap Service
The E engine uses a plastic fuel tank with a non-
replaceable 75 micron in-tank filter screen.  The filter is
welded in the bottom of the tank over a sediment
reservoir.  The tank is mounted above the level of the
carburetor and uses gravity to supply fuel through a
1.   The fuel cap  may not be disassembled; however,
the vent opening on the cap and inner sealing disc
should be kept free of debris.
2.   The venting ability  of the cap may be tested by
filling the cap with water and observing the flow of
water out of the vent opening in the top of the cap.
If water does not drain, the vent opening may be
plugged or restricted.
.25"
I.D. (6.35 mm) rubber hose to the carburetor.  The
fuel hose is friction-fitted to the tank outlet at one end
and to the carburetor at the other end.
The fuel tank is vented through an opening in the fuel
cap.  The fuel opening on the tank is opposite the fuel
outlet, helping to prevent damage to the filter screen by
funnels and gasoline filler spouts that may be inserted
into the fuel tank during refueling.  The placement of
the cap also prevents interference with the starting
rope in Zone Start mower applications.
3.   If the fuel cap  will not vent properly, replace the
entire cap assembly.
4.   Should you encounter  a situation where fuel leaks
around the threads of the fuel cap (not out the
vent), inspect the top of the neck of the fuel tank
and the area in the cap where the fuel tank neck
contacts the cap.  This is the sealing area, not the
threads.  (See Figure 45.)
The fuel cap is a four piece design (see Figure 44) with
an inner sealing disc that is vented to a baffle assembly
in the body of the cap.  The baffle assembly allows
expansion in the tank or splash against the bottom of
the cap, without the loss of fuel. Atmospheric pressure
is allowed into the tank from an opening in the cap to
allow gravity to feed fuel to the carburetor.  (If an
individual part of the cap fails, the entire assembly
must be replaced.)
Figure 45
720-021
Cleaning
1.
Remove the fuel tank.  Take it to an appropriate
area, and wash the tank in clean solvent intended
for cleaning engine parts.
Figure 44
0720-022
2.
Backwash the filter screen by directing cleaning
solvent, under moderate pressure, through the
sediment reservoir and screen, opposite the
direction of fuel flow.
3.
4.
Wash the tank again with clean solvent.
Clean or replace the fuel hose.
29
Product Specification
CategoriesSnow Blower Manuals, Toro Snow Blower
Tags, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,
Model Number38412, 38418, 38413, 38419, 38422, 38424, 38440, 38428, 38429, 38432, 38433, 38437, 38438, 38439, 38440, 38441, 38442, 38445, 38515, 38537, 38538, 38600, 38601, 38602, 38603, 38610, 38611, 38419, 38516, 38517, 38518
Model Year1999, 2000, 2001, 2002, 2004, 2005, 2007
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 65 pages
Document TypeEngine Service Manual
LanguageEnglish
Serial Number240000001 - 240999999
Product NameToro Snow Commander Snowthrower
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower
Product TypeSnowthrower
Product SeriesSingle Stage, Single Stage Snow Commander
Swath24 inch
DischargeSingle Stage
Engine ManufacturerToro
Engine Oil TypeToro 2 cycle / NMMA-TCW3
Engine Motor Model #R-tek
Engine Motor Size7 hp
Engine Motor Type2 Cycle EPA2
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website