4.
5.
6.
7.
Remove the auger/impeller drive belt from the engine
pulley and the large auger/impeller pulley (Fig. 22).
Tip the snowthrower forward and block it so it cannot
fall.
Remove the four screws that secure the bottom cover
to the frame and remove the cover (Fig. 27).
Disconnect the spring from the notch in the bottom
edge of the side plate (Fig. 20).
1
652
Figure 19
1.
Pipe plug
1
3
5.
6.
Check the level of grease in the gear box. The grease
must be visible through the opening.
2
650
Figure 20
If the level of grease is low, add Lubriplate MAG-1
grease (a low temperature, high pressure grease) to the
gear box until point of overflow.
1.
2.
Spring
3. Large traction pulley
Notch in side plate
7.
Install the pipe plug in the gear box.
CAUTION
Adjusting the Traction Drive
POTENTIAL HAZARD
If the speed selector shifts properly but the snowthrower
does not drive in the reverse or forward speeds, adjust the
traction drive.
•
The spring is under heavy tension.
WHAT CAN HAPPEN
•
The spring could be thrown in operator’s or
bystander’s direction.
1.
Pull the wire off of the spark plug and ensure that the
wire does not contact the spark plug.
HOW TO AVOID THE HAZARD
2.
Check and adjust the traction drive as described in
steps 5 through 7 of Installing the Traction Rod on
page 8.
• Use caution when removing the spring.
8.
9.
Set the snowthrower upright.
Loosen the belt guide (Fig. 22).
3.
If the problem persists after adjusting the linkgage,
contact your local Authorized Service Dealer.
10.
Remove the traction drive belt from the engine pulley
and the large traction pulley (Fig. 22).
Replacing the Traction Drive
Belt
11.
12.
Install a new belt around the large traction pulley.
Loop the belt over the engine pulley, ensuring that the
belt is on the inside of the belt guide (Fig. 22).
When the traction drive belt becomes worn, stretched,
oil–soaked, or otherwise damaged, replace the belt. You
can obtain a new belt from your Authorized Service
Dealer.
13.
14.
Tip the snowthrower forward and block it so that it
cannot fall.
Hook the spring into the notch in the bottom edge of
the side plate (Fig. 20).
1.
2.
3.
Pull the wire off of the spark plug and ensure that the
wire does not contact the plug.
15.
16.
Replace the bottom cover with the four screws.
Set the snowthrower upright.
Drain the gasoline from fuel tank. Refer to Emptying
the Fuel Tank on page 22.
Remove the two screws that hold the belt cover in
place and set the cover aside (Fig. 21).
18
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38051, Toro 522 |
| Model Number | 38051 |
| Model Year | 2000 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Serial Number | 000000001 - 000999999, 200000001 - 200999999 |
| Product Name | 522 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Intermediate Frame |
| Swath | 22 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Motor Model # | HSSK50-67401S |
| Engine Motor Size | 5 hp |
| Engine Motor Type | 4 Cycle CARB1, EPA1 |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)