8.
Slide the wheels inward and install the axle pin
through the holes in the wheel hub and through the
inner hole of the axle (Fig. 4).
2. Adjust the two flange nuts up or down on the traction
control rod until the distance between the top of the
handgrip and the bottom of the traction control lever
(Figs. 6 and 7) is approximately 4#/8 in. (11 cm).
1
3
1
3
2
2
473
4
Figure 4
879
1.
2.
Axle pin
3.
Inner axle hole and wheel
hub
Figure 6
Outer axle hole
1.
2.
Auger/impeller control
lever
3.
4.
Speed selector
Speed selector rod
Note: If your snowthrower has the optional tire chains,
install the axle pin through the outer axle holes.
Traction control lever
Installing the Speed Selector
Rod
1
3
1.
2.
3.
Pull the speed selector arm (Fig. 5) to the most
outward position.
4
Move the speed selector (Fig. 6) on the control panel
to the R (reverse) position.
Install the speed selector rod into the selector arm, add
one flat washer on the selector rod, and secure it with a
cotter pin (Fig. 5).
2
665
Figure 7
1.
2.
Traction control lever
Handgrip
3.
4.
4 3/8 in. (11 cm)
3
1 to 2 in. (2.5 to 5 cm)
2
3. Tighten the two flange nuts finger tight.
4.
Move the speed selector (Fig. 6) into third gear.
1
Note: If the speed selector does not move into third gear,
adjust the speed selector before continuing. Refer to
Adjusting the Speed Selector on page 21.
648
Figure 5
5.
Slowly pull the snowthrower backward while slowly
pressing the traction control lever toward the handle.
1.
2.
Speed selector arm
Speed selector rod
3. Flat washer and cotter pin
The adjustment is correct when the wheels stop rolling
backwards and the distance between the top of the
handgrip and the bottom of the traction control lever is
one to two inches (2.5 to 5 cm) (Fig. 7).
Installing the Traction Rod
6.
7.
Adjust the two flange nuts, if necessary, to obtain this
dimension.
1.
Thread the locking flange nut (flange side up) onto the
bottom of the traction control rod, below the loop in
the lower traction rod (Fig. 3).
Tighten the flange nuts securely.
8
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38051, Toro 522 |
| Model Number | 38051 |
| Model Year | 2000 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Serial Number | 000000001 - 000999999, 200000001 - 200999999 |
| Product Name | 522 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Intermediate Frame |
| Swath | 22 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Motor Model # | HSSK50-67401S |
| Engine Motor Size | 5 hp |
| Engine Motor Type | 4 Cycle CARB1, EPA1 |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)