17.
Install the auger/impeller drive belt around the large
auger/impeller pulley and engine pulley, ensuring that
the belt is on the inside of the idler pulley and belt
guide (Fig. 22).
Replacing the Auger/Impeller
Drive Belt
When the auger/impeller drive belt (Fig. 21) becomes
worn, stretched, oil–soaked, or otherwise damaged,
replace the belt. You can obtain a new belt from your
Authorized Service Dealer.
18.
19.
Adjust the belt guide so that there is 1/8 in. (0.3 cm) of
clearance between the belt and the guide, and secure
the belt guide.
Whenever the auger/impeller drive belt needs
replacement, adjust the auger/impeller drive linkage.
Refer to steps 4 through 7 of Installing the
1. Pull the wire off of the spark plug and ensure that the
wire does not contact the spark plug.
2.
Remove the two screws that hold the belt cover in
place and set the cover aside (Fig. 21).
Auger/Impeller Drive Control Linkage on page 9.
20.
Install the belt cover.
Adjusting the Auger/Impeller
Drive Belt
An auger/impeller belt that slips decreases snowthrowing
performance and requires either an adjustment or a new
belt.
2
1
DANGER
661
POTENTIAL HAZARD
•
Improper adjustment may cause injury if the
auger/impeller turns when disengaged.
Figure 21
1.
Belt cover
2. Screw (2)
WHAT CAN HAPPEN
•
The rotating impeller or auger can cut off or
injure fingers or hands.
3.
Loosen the belt guide (Fig. 22).
HOW TO AVOID THE HAZARD
4. Remove the auger/impeller drive belt from the engine
•
Keep your face, hands, feet, and any other part
of your body or clothing away from concealed,
moving, or rotating parts.
Ensure that the impeller brake arm clearance is
maintained.
Do not adjust the auger/impeller drive belt too
tight because it may cause the auger/impeller to
turn when the control lever is in the disengaged
position. If this occurs, decrease belt tension.
pulley and the large auger/impeller pulley (Fig. 22).
5.
6.
Install a new belt around the large auger/impeller
pulley (Fig. 22).
•
•
Loop the belt over the engine pulley, ensuring that the
belt is on the inside of the idler pulley and the belt
guide (Fig. 22).
1.
2.
Pull wire the off of the spark plug and ensure that the
wire does not contact the spark plug.
Check and adjust the belt as instructed in steps 4
through 7 of Installing the Auger/Impeller Drive
Control Linkage on page 9.
3.
Push the spark plug wire onto the spark plug and start
the engine.
4.
5.
Operate the auger/impeller.
If belt still slips, replace the belt.
19
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38051, Toro 522 |
| Model Number | 38051 |
| Model Year | 2000 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Serial Number | 000000001 - 000999999, 200000001 - 200999999 |
| Product Name | 522 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Intermediate Frame |
| Swath | 22 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Motor Model # | HSSK50-67401S |
| Engine Motor Size | 5 hp |
| Engine Motor Type | 4 Cycle CARB1, EPA1 |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)