9.
Remove the bevel gear case/axle case assembly
NOTE: Axle bearing shims are available in 0.008 in.
(0.2 mm), 0.012 in. (0.3 mm), and 0.020 in. (0.5 mm)
thickness.
from the axle support. Coat a new O-ring with grease
andtemporarilyinstalltheaxlecoverassembly.Position
a dial indicator at the tooths center. Prevent the axle
from turning and measure the lower bevel gear to axle
gear backlash (Fig. 20).
11.
27
Tighten axle cover screws from 17 to 20 ft-lb (23 to
N--m).
12.Coat
a new O-ring with grease and install the bevel
LOWER BEVEL GEAR BACKLASH:
gear case/axle case assembly on the axle support.
Tightenmounting screws andnutsfrom35to41 ft-lb(47
to 56 N--m) (Fig. 11).
0.004
to 0.016 in. (0.10 to 0.40 mm)
10.Adjust
backlash by increasing or reducing axle bear-
ingshimthickness (seeAxle Shafts in thissection ofthis
manual).
Differential Shafts
The following procedures assume the rear axle assem-
bly has been removed from the machine.
35
(47
to 41 ft--lb
to 56 N--m)
Removal
1
6
5
IMPORTANT:
Do not interchange right and left dif-
ferential shaft assemblies.
1.
ers. Remove the bevel gear case/axle case assembly
and O-ring from the axle support (Fig. 21).
Remove the mounting screws, nuts, and lock wash-
4
2
3
7
35
(47
to 41 ft--lb
to 56 N--m)
2.
axle support.
Markandpullthedifferentialshaftassemblyfromthe
Figure 21
3.
4.
Remove the retaining ring and bevel gear (Fig 22).
Drive the differential shaft out of the bearings. Re-
1.
2.
3.
4.
Cap screw
Lock nut
Lock washer
Axle support
5.
Bevel gear/axle case
assembly
6.
7.
O-ring
Stud
move the bearings and bearing shims.
5.
damage and wear. Replace components as necessary.
Inspect all gears, shafts, bearings, and cases for
Installation
1.
Press bearings onto differential shaft. Place correct
6
combination of bearing shims in axle support and drive
differential shaft and bearing assembly into axle sup-
port.
3
5
4
2
1
2.
3.
Install bevel gear and retaining ring.
Coat new O-ring with grease. Align differential shaft
splines with differential gear assembly and slide differ-
ential shaft assembly onto axle support.
4.
Bevel Gear Case/Axle Case Assembly in this section of
this manual).
Install bevel gear case/axle case assembly (see
Figure 22
4.
5.
6.
1.
2.
3.
Retaining ring
Bevel gear
Differential shaft
Bearing
Bearing shims
O-ring
Axles, Planetaries, and Brakes (Rev. B)
Page 6 -- 18
Groundsmaster 4500--D/4700--D
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 4500 D, Toro Groundsmaster 4700 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)