Bedbar Removal and Installation
Removal (Fig. 10)
6
1
8
7
1.
Position machine on a clean and level surface, low-
er cutting units, stop engine, engage parking brake, and
remove key from the ignition switch.
2.
Remove the basket from the cutting unit carrier
frame.
3.
4.
5.
Disconnect the drive motor from the cutting unit.
Disconnect the cutting unit from the pull link.
Unhook the cutting unit from the lift arm and slide the
cutting unit out from under the carrier frame.
5
4
2
3 4
5
6.
Loosen the two lock nuts (15) on the end of each
bedbar adjuster assembly.
Figure 11
1.
2.
3.
4.
Sideplate
5.
6.
7.
8.
Washer (metal)
Bedbar
Bedbar pivot bolt
Flange nut
7.
bolt (7).
Loosen the two flange nuts (8) on each bedbar pivot
Rubber bushing
Flange bushing
Washer (plastic)
8.
the washers (4 and 5) from the outside of the cutting unit
side plates.
Remove the two bedbar pivot bolts (7), and each of
4.
(4)
must contact the flange nut (8) (Fig. 11).
Slide one metal washer (5) and one plastic washer
onto each bedbar pivot bolt. The metal washer (5)
9.
and 5) from the inside of the cutting unit side plates.
Remove the bedbar (6) and each of the washers (4
5.
the bedbar arms between washers on each adjuster as-
sembly.
Position bedbar (6) into cutting unit. Slide the top of
10.
ry.
Inspect flange bushings (3) and remove if necessa-
Inspect rubber bushings (2) and remove if necessa-
6.
er (4) between bedbar and each side plate. The metal
washer (5) must contact the bedbar (Fig. 11).
Position one metal washer (5) and one plastic wash-
11.
ry.
Installation (Fig. 10)
7. Install the bedbar pivot bolt assemblies. Tighten
each bedbar pivot bolt from 190 to 240 in–lbs (21 to 27
Nm).
1.
If either rubber bushing (2) was removed from the
side plate, install a new bushing. The bushing should be
installed flush with the inside of the side plate (Fig. 11).
8. Tighten both flange nuts (8) to remove end play at
the outer washers. Do not over tighten the flange nuts
or distort the side plates.
2.
Install the flange bushings (3) with flange facing out-
ward.
9.
assembly until the adjuster spring is fully compressed,
then loosen lock nut 1/2 turn.
Tighten the lock nut (15) on each bedbar adjuster
3.
of each bedbar pivot bolt (7) and apply antiseize lubri-
cant to the threads of each bedbar pivot bolt (7).
Thread the flange nuts (8) all the way up to the head
10.
Adjust cutting unit (see Cutting Unit Operator’s
Manual).
Greensmaster 3100
Page 10 - 11 Rev. D
Dual Point Adjust Cutting units
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 3050, Toro Groundsmaster 3100 |
| Download File |
|
| Document Type | Catalog |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)