Removal (Fig. 3)
Have ProCore Processor attached to tow vehicle
Installation (Fig. 3)
1.
1. Thoroughly clean all parts before assembly.
and park machines on a level surface. Engage vehicle
parking brake, stop engine and remove key from the
ignition switch. Make sure that Processor engine is off.
Chock wheels to prevent movement of either machine.
2.
Assemble wheel hub:
A. If bearing cups were removed from the wheel
hub, press inner and outer cups into the hub until
they seat against the hub shoulder.
2.
Secure lift axle to frame with hitch pin and lynch pin
to prevent lift axle from shifting.
B. Fill hub approximately 50% full of grease.
3.
jack stands (see Operator’s Manual and Jacking In-
structions in Chapter 1 -- Safety).
Jack or hoist machine from ground and support with
C. Pack both bearing cones with grease. Install
greased inner bearing cone into the cup on inboard
side of the wheel hub.
4.
this section).
Remove wheel assembly (see Wheel Removal in
IMPORTANT: The grease seal must be pressed
in so it is flush with the end of the hub. The lip of
the seal must face the inner bearing.
5.
6.
7.
wheel hub to spindle. Slide wheel hub with bearings
from spindle.
Carefully pry dust cap from wheel hub.
D. Lubricatetheinsideofnewgreasesealandpress
it into the wheel hub.
Straighten cotter pin and remove from axle spindle.
Remove slotted hex nut and washer that secure
3.
Install the wheel hub onto the axle spindle taking
care to not damage grease seal in hub.
4.
slotted hex nut onto spindle shaft.
Install greased outer bearing cone, washer and
8.
Disassemble wheel hub:
A. Remove grease seal from the wheel hub taking
care to not damage the hub bore. Discard seal.
5.
While rotating the wheel hub by hand, torque the
slotted hex nut from 75 to 180 in-lb (8.5 to 20.3 N--m)
to seat bearings. Loosen nut until it is away from washer
and hub has end play. Finally, while rotating hub, tighten
slotted hex nut from 15 to 20 in--lbs (1.7 to 2.3 N--m).
B. Remove bearing cones from both sides of wheel
hub. Clean bearings in solvent. Clean inside of hub.
C. If necessary, remove bearing cups from hub.
6.
cap to hub.
Installcotter pintosecureslottedhexnut.Installdust
D. Inspectwheelbearings.Checkthebearingcones
and bearing cups for wear, pitting or other damage.
Replace worn or damaged parts.
WARNING
Failure to maintain proper lug nut torque could
resultinfailureorloss ofwheelandmayresultin
personal injury.
7.
Installwheelassembly(seeWheelInstallation inthis
section).
8.
properly torque lug nuts from 70 to 90 ft--lb (95 to 122
N--m).
Carefully lower machine to ground. Make sure to
9.
Remove lynch pin and hitch pin from lift axle before
using ProCore Processor.
ProCore Processor
Page 6 -- 7
Chassis
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Download File |
|
| Document Type | Catalog |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)