Toro 07155SL Service Manual ProCore 864 1298 Preface Publication

Removal (Fig. 2)
Position aerator on a firm, level surface. If attached
NOTE:  On ProCore  864  machines, there  is  one (1)
thrust washer on each side of the turf guard. On ProCore
1.
1298
machines, there  are two  (2)  thrust washers  on
to tractor, disengage PTO, apply tractor parking brake,
stop engine and remove key from the ignition switch.
each side of turf guard (Fig. 3).
4.
guard and frame.
Place thrust  washer(s)  between each  side  of turf
2.
Disconnect spring assembly from turf guard:
A.  Remove flange nut (item 12) that secures spring
assembly to turf guard.
5.
through frame and into turf guard. Secure pivot shafts to
frame with two (2) carriage screws and flange nuts.
On both sides of frame, slide turf guard pivot shafts
B.  Slide end of cap screw (item 11) from bracket on
turf guard.
6.
Connect spring assembly to turf guard:
C. Position spring assembly away from turf guard.
On both sides of frame, loosen and remove two (2)
A.  Slide end of cap screw (item 11) through bracket
on turf guard.
3.
carriage screws and flange nuts that secure turf guard
pivot shafts to frame.
B.  Secure spring assembly to turf guard with flange
nut.
NOTE:  On ProCore 864 machines, the LH pivot  shaft
extends completely through the LH turf guard and  into
the RH turf guard.
PROCORE 1298
4.
Slide pivot shafts from frame and turf guard.
2
NOTE:  On ProCore  864  machines, there  is  one (1)
thrust washer on each side of the turf guard. On ProCore
1298
machines, there  are two  (2)  thrust washers  on
each side of turf guard (Fig. 3).
3
1
5.
Remove turf guard assembly from machine. Locate
and  retrieve thrust  washer(s)  from  each side  of  turf
guard.
6.
Disassemble  turf  guard  and  spring assembly  as
2
needed using Figure 2 as a guide.
Figure 3
3.   Thrust washer
7.
(item 22) from turf guard.
If necessary, use  press to remove rib neck  screws
1.   Turf guard
2.   Stub shaft
Installation (Fig. 2)
2.410”
to 2.530”
1.
press to install  screws into turf guard.  Make sure that
screw heads are flush with turf guard surface.
If rib neck screws were removed from turf guard, use
(61.2
to 64.2 mm)
5.940”
to 6.060”
(150.9
to 153.9 mm)
2.
Assemble turf guard and spring assembly as needed
using Figure 2 as a guide. If spring assembly was taken
apart, use dimensions shown in Figure 4 during the as-
sembly process.
3.
Make sure that keyed flange bushing (item 16) is cor-
rectly placed  in  each end  of turf  guard.  Position turf
guard assembly to aerator.
Figure 4
ProCore 864/1298
Page 3 − 5
Chassis
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 72 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website