Toro 07155SL Service Manual ProCore 864 1298 Preface Publication

C. Mount a dial indicator with a magnetic base to the
vise  so  that the  dial  indicator  touches  the  pliers
3.100”
LOCKING PLIERS
(LIGHTLY CLAMPED)
(78.7
mm)
3.100”
(78.7 mm) from the center of the input shaft.
D. Rotate  the pliers  and monitor the  dial indicator
reading to check gearbox backlash. Allowable back-
lash is from 0.006” to 0.013” (0.16 to 0.33 mm).
E.  If backlash adjustment is necessary, remove gas-
ket(s) from between quill and gearbox housing to de-
crease  backlash.  Increase  backlash by  installing
additional  gasket(s). Recheck  backlash  after  any
gasket change. Repeat process until backlash is cor-
rect.
DIAL
INDICATOR
F.  Remove gearbox from vise.
SOFT JAWED
VISE
8.
After backlash is correct, check  gear pattern to as-
sure that proper gear mesh exists:
Figure 42
A.  Remove quill  housing assembly and  coat gear
teeth on cross shaft with gear mounting compound.
GEAR PATTERN REQUIREMENTS
B.  Install quill housing  into gearbox housing using
the same number of gaskets and secure with six (6)
flange head screws. Torque  screws 81 ft−lbs (109
N−m).
0.118” (3.0 mm)
MINIMUM
0.118” (3.0 mm)
MINIMUM
40%
Tooth Width
to 80% of
C. Rotate  the input  shaft to establish  a gearmesh
pattern in the gear mounting compound. Rotating the
input shaft 1/2 turn will allow all cross shaft gear teeth
to contact input shaft gear teeth.
TOE
HEEL
20%
Tooth Height
to 50% of
D. Remove quill assembly from gearbox and inspect
the pattern on the gear teeth.
0.197”
(5.0 mm)
MINIMUM
E.  Ideal pattern should cover from 40% to 80% of the
gear face width (Fig. 43). The contact area should be
in the center of each tooth and extend from 20% to
Figure 43
50%
of the gear face height. The pattern should not
run off the tooth heel, toe or top.
F.  If  necessary, adjust the  number of soft  shim(s)
between housing and inner bearing cone to correct
gear pattern.  Make sure  to also check  and adjust
cross shaft end play.
2
4
G. Recheck backlash if any changes are made. Ad-
just backlash if necessary.
9.
Apply a light coating of grease on seal lips and seal
3
OD. Install seals into gearbox bores taking  care to not
damage  seals  during   installation.  Seals  should  be
installed until they are flush with the housing.
1
Figure 44
1.
2.
Input gear and shaft
Cross shaft
3.
4.
Gasket location
Soft shim location
Coring Head
Page 4 − 44
ProCore 864/1298
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 72 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website