Toro 07155SL Service Manual ProCore 864 1298 Preface Publication

Driveshaft Cross and Bearing Service
1.
moval in this section).
Remove driveshaft from aerator (see Driveshaft Re-
5.  Make sure that assembled joint moves without bind-
ing. Slight binding  can usually be eliminated by  lightly
rapping the yoke lugs with a soft faced hammer. If bind-
ing continues,  disassemble joint  to identify  source of
binding.
IMPORTANT: When   placing  yoke  in  vise,  clamp
lightly on the solid part of the yoke to prevent yoke
damage. Also, the use of a vise with soft jaws is rec-
ommended.
6.  If driveshaft halves were separated during cross and
bearing service, note that splines on shaft and tube have
a blind spline to ensure alignment of end yokes when the
driveshaft is assembled. Align blind spline in shaft and
tube when assembling driveshaft halves.
2.
secure bearings in each yoke. Remove yoke from vise.
Lightly clamp yoke in vise. Remove snap rings that
IMPORTANT: Yokes  must  be  supported when  re-
moving and installing bearings to prevent damage.
7.
Install driveshaft to aerator (see Driveshaft Installa-
tion in this section).
3.
Use  a press  to  remove cross  and  bearings from
yokes:
4
A.  Place a small socket against one bearing and a
large socket against the yoke on the opposite side.
3
B.  While supporting  the large  socket, apply  pres-
sure on small  socket to partially push the  opposite
bearing into the large socket.
1
C. Remove   yoke  from  press,  grasp  partially  re-
moved bearing  and tap  on yoke to  completely re-
move the bearing.
D. Repeat process for remaining bearings.
E.  Thoroughly clean and inspect all components.
To install new cross and bearings:
3
2
4.
Figure 39
A.  Apply a coating of grease to bearing bores of end
yoke and shaft yoke. Also, apply grease to bearings
and seal  of  bearing assembly.  Make sure  that all
bearing rollers are properly seated in bearing cage.
1.
2.
End yoke
Cross and bearing kit
3.
4.
Snap ring (4 used)
Shaft yoke
B.  Press one bearing partially into yoke.
IMPORTANT: Take  care  when  installing  cross
into bearing to avoid damaging bearing seal.
C. Carefully insert cross into bearing and yoke.
D. Hold cross in alignment and press bearing in until
it hits the yoke.
E.  Carefully place  second bearing  into yoke  bore
and onto cross shaft. Press bearing into yoke.
F.  Install snap rings to secure bearings in place.
G. Repeat procedure for other yoke.
H. Grease cross until grease comes out of all four (4)
bearing cups.
Coring Head
Page 4 − 38
ProCore 864/1298
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 72 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website