Toro 07155SL Service Manual ProCore 864 1298 Preface Publication

Removal (Fig. 32)
Position aerator on a firm, level surface. If attached
to tractor, disengage PTO, apply tractor parking brake,
stop engine and remove key from the ignition switch.
Installation (Fig. 32)
1.
1.  Make sure that coring frame is supported in a raised
position to prevent unexpected lowering of coring frame.
2.
3.
Position depth control assembly to coring frame.
Secure depth control assembly to coring frame with
2.
Remove rear hood from machine.
3.
Remove front cover to allow access to depth control
four (4) carriage screws and flange nuts.
assembly (see Cover Removal in the  Service and Re-
pairs section of Chapter 3 − Chassis).
4.
depth control assembly is supporting coring frame.
Use appropriate hoist to lower coring frame so  that
4.
compress coring  head compression spring(s)  slightly.
The springs do not have to be removed from machine.
Use compression spring tool (see Special Tools) to
5.
compression spring(s):
Remove compression spring tool from  coring head
A.  Loosen lower nut on threaded rod to allow spring
(item 2) to extend. Make sure that upper spring cup
(item 1) extends into spring seat on hitch frame.
A.  Install  compression  spring  tool   threaded  rod
through holes in each spring cup (item 7), then install
washer and nut on both ends of rod.
B.  Remove compression  spring  tool  components
(threaded rod, washers and nuts) from spring.
B.  Tighten upper  nut  on  rod  to compress  spring
(item 6) until upper spring cup is approximately 1/2”
(13
mm) from spring seat on hitch frame.
C. If  working  on ProCore  864,  repeat for  second
spring.
C. If  working  on ProCore  864,  repeat for  second
compression spring.
6.
7.
Adjust aerator to desired depth setting.
Install front cover to machine (see Cover Installation
in the Service and Repairs section of Chapter 3 − Chas-
sis).
CAUTION
The ProCore  864  coring head  frame assembly
weighs approximately 900 pounds (408 kg). The
ProCore   1298  coring   head   frame   assembly
weighs  approximately   675  pounds   (306  kg).
Make sure that proper lift or hoist is used to sup-
port coring head frame during repairs.
8.
Install rear hood to machine.
2
5.
Use suitable lift or hoist and lifting eyelets on coring
crankshaft as lift  points (Fig. 33) to raise  coring head.
Raise  coring head  so that  clearance  exists between
depth control assembly and pad on hitch frame.
1
6.
Use appropriate  jackstands or blocking  to support
the coring head to prevent it from shifting or lowering.
7.
Remove four  (4) carriage  screws and  flange nuts
that secure depth control assembly to coring frame.
8.
Remove depth control assembly from coring frame.
Figure 33
1.
Bearing housing
2.   Lifting eyelet
ProCore 864/1298
Page 4 − 33
Coring Head
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 72 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website