Toro 07155SL Service Manual ProCore 864 1298 Preface Publication

5.
position on idler spring mount. Loosen idler nut (item 16)
to remove idler tension on drive belt.
Loosen lock nut  (item 15) that  secures idler nut  in
2
CAUTION
1
Be careful when lifting the idler pulley. The idler
pulley is spring loaded and may cause personal
injury.
6.
Lift and hold idler pulley away from belt. Remove belt
from drive pulley. Carefully lower idler pulley.
Figure 24
7.
Loosen and  remove two (2) flange  nuts and hard-
ened  D washers  that  secure rotolink  damper  for  #1
stomper arm (see Rotolink Damper Disassembly in this
section). Lower rotolink damper from coring head frame.
1.
Drive belt
2.
#1 stomper arm
8.
Remove  drive  belt  from  driven  pulley  on  coring
crankshaft.
2
9.
Route drive  belt down  through coring  head frame
and around lower end of #1 stomper arm to remove cor-
ing head drive belt from machine (Fig. 24 and 25).
Installation (Fig. 22)
1.
Route drive belt around lower end of #1 stomper arm
and up through coring head frame (Fig. 24 and 25).
1
2.
Position drive belt to driven pulley  on coring crank-
shaft.
Figure 25
3.
install belt onto drive pulley (Fig. 23).
Lift idler pulley, route drive belt under idler pulley and
1.
Drive belt
2.
#1 rotolink damper
4.
Apply tension  to idler  pulley by adjusting  idler nut
(item 16) until compression spring length is 5.750” (145
mm). Secure idler nut location with lock nut (item 15).
1
2
5.
Raise rotolink damper for #1 stomper arm to coring
4
3
head  frame.  Make  sure  that  damper  standoffs  and
bumper are on damper studs. Secure damper to coring
head frame with two (2) D washers and lock nuts  (see
Rotolink Damper Assembly in this section).
5
6.
Make sure that tinnerman nuts (item 1), flat washer
(item 8) and cap screw (item 9) are on frame.  Position
belt guard to machine. Secure belt guard to support with
flange nut (item 7), two (2) flange head screws (item 6)
and flat washers (item 5).
5.750”
(145
mm)
7.
tion in the Service and Repairs  section of Chapter 3 −
Chassis).
Install pulley shield to machine (see Cover Installa-
Figure 26
1.
2.
3.
Idler pulley
Drive belt
4.
5.
Idler nut
Lock nut
Compression spring
8.
Install rear hood to machine.
ProCore 864/1298
Page 4 − 25
Coring Head
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 72 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website