Toro 07155SL Service Manual ProCore 864 1298 Preface Publication

Removal (Fig. 27)
Position aerator on a firm, level surface. If attached
to tractor, disengage PTO, apply tractor parking brake,
stop engine and remove key from the ignition switch.
C. As drive pulley (item 6) is being installed, place 0,
or 2 shims (item 5) between outer shaft bearing and
drive pulley to align drive pulley with driven pulley on
coring crankshaft. Pulleys should be  aligned within
1
1.
0.070”
(1.8 mm).
2.
Remove rear hood from machine.
D. Install a .375” − 16 UNC − 2B screw into one of the
threaded pulley holes leaving 1” to 2” of the screw ex-
tending from the pulley surface. Make sure that the
end of the screw does not contact pulley drive hous-
ing. Use a suitable pry bar between the pulley flange
and screw extension to prevent the pulley and pulley
shaft from rotating.
3.
(see Cover Removal in the Service and Repairs section
of Chapter 3 − Chassis).
Remove front cover and pulley shield from machine
4.
Drive Belt Removal in this section).
Remove coring  head drive  belt (see  Coring Head
E.  Secure drive pulley to pulley shaft with flat washer
and cap screw. Torque cap screw from 210 to 230 ft−
lb (285 to 311 N−m).
5.
Removal in this section).
Remove driveshaft from pulley shaft (see Driveshaft
6.
Remove pulley (item 6) from pulley shaft:
F.  Remove screw from pulley hole.
A.  Install a .375” − 16 UNC − 2B screw into one of the
threaded pulley holes leaving 1” to 2” of the screw ex-
tending from the pulley surface. Do not tighten screw
with a wrench. Use  a suitable pry bar between  the
pulley  flange and  screw extension  to  prevent the
pulley and pulley shaft from rotating.
2.
Belt Installation in this section). Make sure that drive belt
is properly tensioned.
Install coring head drive belt (see Coring Head Drive
3.
Installation in this section).
Install  driveshaft  to  pulley  shaft   (see  Driveshaft
B.  Remove cap screw and flat  washer that secure
pulley to pulley shaft.
4.
Cover Installation in the Service and Repairs section of
Chapter 3 − Chassis).
Install front cover and pulley shield to machine (see
C. If needed, the use of three (3) .375” − 16 UNC −
2B screws (see Special Tools) can be installed into
threaded holes  of pulley  to  aid in  pulley removal.
Tighten screws  progressively and  evenly until  the
pulley is loose on the pulley shaft.
5.
Install rear hood to machine.
3
7.
Remove additional components as necessary using
Figure 27 as a guide.
Installation (Fig. 27)
2
1.
Install all removed components using Figure 27 as a
guide.
1
A.  If pulley shaft (item 2) was removed, apply anti-
seize lubricant to shaft bearing surface before sliding
shaft into bearing bores.
4
B.  Apply antiseize lubricant to splines of pulley shaft
(item 2) before installing pulley and driveshaft.
Figure 28
1.
2.
Drive pulley
Idler pulley
3.
4.
Driven pulley
Drive belt
ProCore 864/1298
Page 4 − 27
Coring Head
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 72 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website