General Information
Storage
It is very important that the water system be drained
to avoid freezing and damaging the components.
Drain system as follows:
2. Remove and discard the oil filter. Install a new filter.
3.
Refill the engine with 3 qts. of recommended SAE
wt. motor oil.
30
1. Stop engine, remove key from ignition switch and
remove wires from spark plugs.
4.
utes. DO NOT RUN LONGER THAN TWO MINUTES.
Start the engine and run at idle speed for two min-
2.
Remove (2) screws securing drive shield to frame
and remove shield.
5.
6.
holes.
Stop the engine; remove the spark plugs.
Pour one ounce of clean engine oil into spark plug
3.
With the engine ”OFF” and key removed from igni-
tion, rotate the drive coupling by hand until resistance is
felt. Continue to rotate the coupling about 1/4 revolution,
opening the cycling valve.
7.
with the starter for a least 12 revolutions to distribute oil
in the cylinders.
With the spark plugs removed, crank the engine
4.
Using the appropriate reducers (National Pipe
8.
Reinstall spark plugs.
thread), connect a source of compressed air (maximum
pressure 150 psi – minimum pressure 90 psi) to the wa-
ter inlets on either side of machine.
9. Drain the gasoline from the fuel tank and fuel lines.
Reinstall all lines and secure all connections.
DANGER: Compressed air can penetrate the skin
and cause physical harm. Use extreme caution and
wear protective goggles and gloves when working
with high pressure air. Get prompt medical attention
if an injury occurs.
10. Thoroughly clean and service the air cleaner.
11.
Check the oil filler cap and fuel tank cap to ensure
they securely in place.
Traction Unit
5.
Let compressed air flow through the machine for 3
1.
2.
Thoroughly clean machine.
minutes. While compressed air is flowing, temporarily
open the spray wash and high pressure drain valve,
purging water from the spray wash and high pressure
system.
Grease or oil all fittings or pivot points.
3.
30
Check to make sure all tires are over inflated to 20 –
p.s.i.
6.
the drive shield previously removed and tighten the re-
lief valve tube.
Disconnect compressed air and reducers. Reinstall
4.
Lightly sand and use touch up paint on all areas that
are scratched, chipped or rusted.
Drain and replace hydraulic oil and filter on cam
gear case.
5.
7.
new filter and replace the filter container.
Remove and drain the water filter container. Install
6.
7.
Drain and replace oil in water pump case.
Clean the battery, terminals and posts with a wire
Engine
brush and baking soda solution. Coat cable terminals
and battery posts with skin over grease or petroleum jel-
ly. Recharge battery.
1.
drain cap.
Drain the engine oil from the oil pan and replace the
General Information
Hydroject 3010
Page 6 – 38
Rev. B
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Hydroject 3010 |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)