3.
Install shaft with bearings and spacer into housing and
secure with retaining ring.
Apply grease to the bore of the bearing housing.
7. Install reel drive belt to the reel drive assembly and
adjust belt (see Reel Drive and Transmission Coupler
Drive Belt Replacement in this section). Make sure that
bearing housing flange nuts are securely tightened after
drive belt adjustment.
4.
Fill small cavity between outer bearing and seal loca-
tion in bearing housing approximately half full of Mobil
High Temperature XHP–222 grease (or equivalent)
(Fig. 8).
8. Install reel drive belt cover and secure with flange
nut. Torque flange nut 100 in–lb (11.3 N–m).
5.
ture XHP–222 grease (or equivalent) (Fig. 8). Install oil
seal into housing.
Pack rear cavity of oil seal with Mobil High Tempera-
9. Attach cutting unit to the traction unit (see Separating
Cutting Unit From Traction Unit in the General Informa-
tion section of Chapter 7 – Cutting Unit).
NOTE: When installing flex coupler onto shaft, do not
mar outer surface of coupler (e.g. grasping with pliers or
mounting in vise) as coupler may be damaged and fail
prematurely.
10.Connect spark plug wire to spark plug.
2
6.
Slide coupler onto shaft and secure with new spring
pin.
1
Installation
1.
Park machine on a level surface. Make sure engine
is OFF. Remove spark plug wire from the spark plug.
2.
Position bearing housing with shaft and coupler to
the plate assembly.
3.
Place both carriage screws through the bearing
housing and plate. Install washers and flange nuts on
carriage screws. Do not fully tighten flange nuts at this
time.
Figure 7
1.
Bearing housing (LH)
2.
Carriage screw
4.
shaft keyslot.
Position spacer onto shaft. Place woodruff key into
Mobil High Temp
XHP–222 Grease
2
2
1
5.
Apply antiseize lubricant to the bore of the pulley and
install pulley onto shaft:
A. Left side pulley uses a pulley washer.
B. Right side pulley should be installed with the
flange outward.
3
NOTE: Do not grasp hex shaft when tightening flange
nut that secures pulley as flex coupler may be damaged
and fail prematurely.
Mobil High Temp
XHP–222 Grease
6.
flange nut from 40 to 50 ft–lb (54 to 68 N–m).
Secure the pulley to the shaft with flange nut. Torque
Figure 8
1.
2.
Shaft
3.
Seal
Bearing
Traction and Reel Drive System
Page 4 – 8
Greensmaster Flex 18/21
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Greensmaster 04018, Toro Greensmaster 04019, Toro Greensmaster 04022, Toro Greensmaster 04024, Toro Greensmaster 04025, Toro Greensmaster 04030, Toro Greensmaster 04031 |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 3 out of 3)
Lawn and Garden readers have rated Toro 06149SL Models 04018 04019 04030 04022 04024 04025 04031 Service Manual 3.0 out of 3.0 based on 1 product reviews. i gone through your website about Safety Shoes Manufacturers & Distributors
its really amazing. if you want additional information about Safety Shoes Manufacturers & Distributors contact Us.
Safety Shoes Manufacturers & Distributors.