8.
If traction band is replaced, the new band will have
an ink mark on the upper end of the band (Fig. 28).
MARK LOCATION
9.
Carefully fit traction shaft with band to the planetary
assembly and gearbox base taking care not to distort
traction band. Traction band should easily slide over
traction drum during installation. If traction band is im-
properly placed on the traction shaft or if the band is dis-
torted, it will not fit easily on the drum. Check that
planetary assembly is free to rotate with band installed.
Note: On Flex 21, if gearbox is still attached to engine,
traction lever on engine side of gearbox should be instal-
led onto traction shaft is shaft is installed into gearbox.
1
2
10.Rotate
differential shaft to verify that all gears and
shafts are meshed properly.
Figure 28
11.
Use dowel pins to position gasket to gearbox base.
1.
Traction shaft
2.
Traction band
12.Lubricate
box cover to shafts and fit cover to the gearbox base.
short differential axle shaft. Position gear-
1
6
13.Position
drive shaft plate to gearbox with three fas-
3
teners: two socket head screws (shorter) and one cap
screw with lock washer. Install four socket head screws
(longer) and washers in remaining holes in gearbox cov-
er. Torque gearbox fasteners from 120 to 140 in–lb
(13.6
to 15.8 N–m) in the sequence shown in Figure 29.
5
14.Place
traction drive lever onto gearbox shaft noting
4
2
location of alignment splines on shaft and lever. Mount
traction lever with cable boss outward (Fig. 30). Secure
lever with cap screw and lock nut. Parking brake lever
installation should be done with cable attached to lever
as gearbox is being installed on machine.
Figure 29
15.Check
gearbox operation:
3
A. Engage and disengage clutch, brake band and
traction band. Check for smooth engagement.
2
B. Turn one differential axle shaft and check that
other shaft rotates in opposite direction.
1
C. If smooth operation is not detected, correct prob-
lem before completing assembly.
3
16.Install
reel drive assembly to the gearbox (Fig. 22):
Figure 30
1.
2.
Traction drive lever
Parking brake lever
3.
Cable mounting boss
A. Apply antiseize lubricant to the bore of the reel
drive pulley. Place woodruff key in gearbox shaft and
slide pulley and pulley washer onto shaft. Thread
flange nut onto shaft.
B. Position reel drive belt over pulleys and properly
tension belt (see Transmission Coupler Drive Belt
Adjustment in this section).
C. Tighten flange nut to secure pulley.
Greensmaster Flex 18/21
Page 4 – 21
Traction and Reel Drive System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Greensmaster 04018, Toro Greensmaster 04019, Toro Greensmaster 04022, Toro Greensmaster 04024, Toro Greensmaster 04025, Toro Greensmaster 04030, Toro Greensmaster 04031 |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 3 out of 3)
Lawn and Garden readers have rated Toro 06149SL Models 04018 04019 04030 04022 04024 04025 04031 Service Manual 3.0 out of 3.0 based on 1 product reviews. i gone through your website about Safety Shoes Manufacturers & Distributors
its really amazing. if you want additional information about Safety Shoes Manufacturers & Distributors contact Us.
Safety Shoes Manufacturers & Distributors.