Interlock Module and Switch
The interlock module prevents the engine from starting
unless the interlock switch is closed (traction lever in
NEUTRAL). After a safe start, the engine will continue
to run with the interlock switch open (traction lever FOR-
WARD) or closed.
C. Ground the red wire (male connector) to the en-
gine block and attempt to start the engine. The en-
gine should not start.
D. Connect the red wire to the black wire.
4.
harness. Position engine ON/OFF switch to ON.
Disconnect interlock switch on handle from wiring
If the engine will not start, perform the following tests to
determine if the interlock module or interlock switch is at
fault.
A. Attempt to start the engine. The engine should
not start.
1.
Check that there is a good ground between the inter-
lock module (green wire) and the engine (Fig. 5). Check
all other electrical connections and the interlock module
for damage. Repair or replace any damaged wiring or
components.
B. Jumper across the wire harness connector termi-
nals and attempt to start the engine. The engine
should start.
C. Remove jumper and connect interlock switch to
wiring harness.
2.
switch (located on equipment handle).
Check the adjustment and continuity of the interlock
5.
in step 3 or 4.
Replace interlock module if it fails either of the tests
A. Disconnect interlock switch wire connector from
wiring harness.
B. Place traction lever in the FORWARD position.
The switch should be open (no continuity).
4
2
C. Place traction lever in the NEUTRAL position.
The switch should be closed (continuity).
D. Adjust interlock switch until it opens and closes
properly when the traction lever is in the FORWARD
and NEUTRAL positions (See Interlock Switch in the
Service and Repairs section of this Chapter).
1
3
5
6
E. Connect interlock switch to wiring harness.
3.
With engine ON/OFF switch in the ON position, at-
tempt to start the engine. If the engine does not start,
check the interlock module using the following steps:
Figure 5
A. Disconnect red wire (male connector) where it
connects to the black wire leading to the ignition coil
(Fig 5).
1.
2.
3.
Wire harness
Interlock module
Stop switch wire
4.
5.
6.
Armature wire
Ground connection
Wires to interlock switch
B. Attempt to start the engine. The engine should
start.
Lighting Coil
The engine on the Greensmaster Flex 18 and Flex 21 is
equipped with a lighting coil to provide electrical current
for an optional lighting kit. The coil is located under the
engine flywheel and uses permanent magnets on the
flywheel to operate. See the Kawasaki FE120 Service
Manual at the end of Chapter 3 – Engine for lighting coil
testing information.
Greensmaster Flex 18/21
Page 5 – 7
Electrical System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Greensmaster 04018, Toro Greensmaster 04019, Toro Greensmaster 04022, Toro Greensmaster 04024, Toro Greensmaster 04025, Toro Greensmaster 04030, Toro Greensmaster 04031 |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 3 out of 3)
Lawn and Garden readers have rated Toro 06149SL Models 04018 04019 04030 04022 04024 04025 04031 Service Manual 3.0 out of 3.0 based on 1 product reviews. i gone through your website about Safety Shoes Manufacturers & Distributors
its really amazing. if you want additional information about Safety Shoes Manufacturers & Distributors contact Us.
Safety Shoes Manufacturers & Distributors.