Toro 08158SL Rev A Service Manual ProForce Debris Blower Preface Publication

Removal (Fig. 2)
Position machine on a firm, level surface. Make sure
engine is  stopped  and remove  key from  the ignition
switch. Chock wheels to prevent machine from moving.
6.  Install top grill to machine (Fig. 4).
1.
7.  Connect negative battery cable to negative  battery
terminal. Tighten nut that secures battery cable from 10
to 15 ft--lb(14 to 20 N--m).Make sure that battery cover
is secured.
2.
To prevent unexpected machine operation, discon-
nect the negative battery cable from the battery terminal
(see Battery Service in the Service and Repairs section
of  Chapter  4 --  Electrical  System).  Position  discon-
nected negative cable away from the negative  battery
terminal.
12
11
10
9
3.
(Fig. 4).
Removetopgrilltoallowaccess   toblower  driveshaft
8
4.
securedriveshaftassemblytohubsonengineshaftand
blower shaft.
Remove cap screws, flat washers and lock nuts that
7
2
1
3
5.
Lift drive shaft assembly from machine.
4
300
(34 to 37 N--m)
to 330 in--lb
5
Loctite #242
6.
Figures 2 and 3 as guides. Note differences in coupling
spacer flange thickness for assembly purposes.
Disassemble drive couplings from drive shaft using
6
Figure 3
1.
Cap screw
7.
8.
9.
Shaft hub
7.
necessary.
Inspect drive  couplings for damage  and replace if
2.
3.
4.
5.
6.
Flat washer
Cap screw
Spacer
Flat washer
Flange nut
10. Spacer
8.
blower shaft:
If necessary,  remove hubs  from engine shaft  and
Cap screw
Woodruff key
11. Drive coupling
12. Fan hub/coupling
A.  Remove cap screw and flat washer that secure
hub to shaft.
4
1
3
NOTE:  HubhasataperedIDandwillrequireapuller
to remove it from shaft.
1
2
1
B.  Use appropriate puller to remove hub from shaft.
C. Remove woodruff key from shaft slot.
Installation (Fig. 2)
2
1
5
1.
If hub  was  removed from  engine shaft  or blower
3
shaft, thoroughly clean tapers of shaft(s) and hub(s). Fit
woodruff key to shaft slot and place hub on shaft. Apply
Loctite #242  (or equivalent)  to threads  of cap  screw
usedtosecurehubtoshaft.Securehubtoshaftwithcap
screw and flat washer.
2.
3.
Place coupling spacers into rubber coupling.
Figure 4
Securedrivecouplingstodriveshaftwithcapscrews
and lock nuts using Figures 2 and 3 as guides.
1.
2.
3.
Screw
Washer
Flange nut
4.   Top grill
5.   Side grill
4.
Position drive  shaft assembly to  engine shaft and
blower shaft.
5.
and blower shaft with cap screws, flat washers and lock
nuts.
Secure drive shaft assembly to hubs on engine shaft
ProForce Debris Blower
Page 5 -- 5
Blower Assembly
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 83 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website