Toro 08158SL Rev A Service Manual ProForce Debris Blower Preface Publication

7.
guard (item  13), route  v--belt from behind  guard and
carefully remove belt from machine.
Loosen cap screws and flange nuts that secure belt
1
8.
and nozzle pulley from  outer housing using Figures 9
and 12 as guides.
If necessary, remove nozzle guides, pulley bearings
3
Installation (Fig. 9)
1.
nozzle guides using Figures 9 and 12 as guides.
If removed, install nozzle pulley, pulley bearings and
3
4
2.
Place v--beltinnozzle pulley,route  behind beltguard
(item 13) and install belt on motor pulley.
2
3.
With a 3/8 in. drive  torque wrench, pivot the motor
Figure 10
bracket from 200 to 230 in--lb (23 to 25 N--m) to set v--
belt tension (Fig. 10). Do not over tension belt. Hold
bracket  with the  torque  wrench  and tighten  two  (2)
flange head screws and flange nuts to secure belt ad-
justment and nozzle motor bracket.
1.
2.
Drive pulley
3.
4.
Flange head screw
Leaf spring assembly
Torque wrench access
2
1
4.
Center belt guard around v--belt.Tighten cap screws
4
and flange nuts to secure belt guard to machine.
5.
position bearing to leaf spring and secure with shoulder
bolt and lock nut.
If bearing was  removed from leaf  spring (Fig. 11),
UP
3
NOTE:  When installing the  leaf spring assembly,  the
leaf spring bearing mounting loops should be orientated
up.
Figure 11
1.
2.
Leaf spring
Lock nut
3.
4.
Shoulder bolt
Bearing
6.
5)
Position leaf spring assembly and flat washers (item
tobracket. Makesurethatfive(5)washers    areplaced
between spring and bracket at each mounting hole. The
bearingontheleafspringshouldbecenteredontheout-
side of the v--belt. Secure leaf spring to motor bracket
with two (2) cap screws (item 21) and flange nuts (item
22).
1
2
7.
head screw  and lock  nut to  secure nozzle  to pulley.
Fit nozzle and nozzle clamp to pulley. Tightensocket
Torque fasteners from 45 to 50 in--lb (5.1 to 5.6 N--m).
8.
Connect negative battery cable to negative battery
6
terminal. Tighten nut that secures battery cable from 10
to 15 ft--lb(14 to 20 N--m).Make sure that battery cover
is secured.
5
3
4
6
Figure 12
1.
2.
3.
Outer housing
Nozzle pulley
Cap screw
4.
5.
6.
Nozzle guide (4 used)
Flange nut
Spacer
ProForce Debris Blower
Page 5 -- 11
Blower Assembly
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 83 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website