Toro 08164SL Service Manual Workman MDE Preface Publication Service

Accelerator System Calibration
The accelerator system on the Workman MDE includes
the accelerator pedal assembly, the accelerator poten-
tiometer, the accelerator switch and the controller. Ifany
of  these  components are  adjusted,  removed  or  re-
placed, the  following calibration procedure  should be
performed. Additionally, if vehicle movement is erratic,
jerky or if the diagnostic light on the dash is flashing six
1
4
(6)
times, calibration of the accelerator system  should
be performed.
1.
OFF and remove key. Raise box and secure with prop
rod. Remove controller cover.
Position vehicle on a level surface, turn on/off switch
2
3
2.
necessary (see Accelerator  Switch Adjustment in this
section).
Check accelerator switch  adjustment and adjust  if
Figure 16
1.
2.
Controller
Gray controller lead
3.
4.
Ground post (B--)
Controller LED
3.
Check  accelerator potentiometer  adjustment  and
adjust if necessary (see Accelerator Potentiometer Ad-
justment in this section).
4.
ground post (B--) on controller (Fig. 16).
Using a jumper wire, connect gray controller lead to
NOTE:  Duringcalibration,thevehiclestatuslightonthe
dash should flash the same as the controller LED.
5.
the controller LED should flash six (6) times.
Turn on/off switch ON. The alarm should sound and
6.
Slowly depress accelerator pedal untilthe alarmmo-
mentarily stops and hold pedal in position. This should
takeaverysmallmovementofthepedal.Oncealarmre-
sumes, release accelerator pedal completely.
7.
Depress and hold accelerator pedal fully. Alarm will
momentarily  stop while  controller  calibration occurs.
Holdpedalfullydepresseduntilalarmresumesandthen
release pedal.
8.
Ifcalibrationprocesswassuccessful,alarmwillchirp
anddiagnosticlightonthedashwillbelitcontinuous(not
flashing). If  alarm continues to  sound or if  diagnostic
light is flashing, turn on/off switch OFF and repeat steps
5,
6 and 7.
9.
jumper  wire from  gray controller  lead  and controller
ground post (B--).
Turn on/off switch OFF and remove key. Disconnect
10.Install
controller cover and lower box.
11.
If vehicle operation continues to be erratic after com-
pleting the  accelerator system  calibration procedure,
evaluate the components in the accelerator system: ac-
celerator switch, accelerator potentiometer, accelerator
pedal, circuit wiring and controller.
Workman MDE
Electrical System
Page 3 -- 13
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 112 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website