Toro 08164SL Service Manual Workman MDE Preface Publication Service

Removal (Fig. 3)
Park machine on  a level surface, stop  engine, set
6
4
1.
5
parking brake and remove key from the ignition.
3
7
WARNING
2
Beforejackingupthemachine,reviewandfollow
Jacking Instructions in Chapter 1 -- Safety.
8
2.
off the ground and support vehicle with appropriate jack
stand beneath the frame.
Chock wheels not being jacked up. Jack front wheel
9
Loctite #242
1
Figure 4
3.
chine.
Remove lug nuts and pull wheel assembly from ma-
1.
2.
3.
4.
5.
Outer bearing cone
Outer bearing cup
Wheel hub
6.
7.
8.
9.
Inner bearing cone
Seal
Socket screw (4 used)
Wheel stud (5 used)
4.
Caliperinthissection).Positioncaliperawayfromwheel
hub and spindle.
Remove brake caliper from spindle (see Front Brake
Brake rotor
Inner bearing cup
5.
6.
7.
Slide wheel  hub  with bearings  and brake  rotor from
spindle.
Carefully pry dust cap from wheel hub.
1
Remove cotter pin and nut retainer from spindle.
Remove jam nut that secures wheel hub to spindle.
2
75
to 100 ft--lb
(102 to 135 N--m)
8.
Disassemble the wheel hub (Fig. 4):
A.  Pull the seal out of the wheel hub.
3
B.  Remove bearings from both sides  of the wheel
hub. Clean bearings in solvent. Make sure bearings
are in good operating condition. Clean the inside of
the wheel hub. Check the bearing cups for wear, pit-
ting or other  noticeable damage. Replace  worn or
damaged parts.
4
5
6
Figure 5
C. Ifnecessary,remove  wheel studsandbrakerotor
from wheel hub.
1.
2.
3.
Cap screw
Brake hose clip
A--arm (LH shown)
4.
5.
6.
Kingpin sleeve
Thrust washer
Lock nut
9.
Remove spindle (Fig. 5):
Installation (Fig. 3)
A.  Remove cotter pin and castle nut securing tie rod
ball joint to the spindle. Separate ball joint from the
spindle. Remove tie rod from  steering gearbox pit-
man arm if necessary.
1.
Install spindle as follows (Fig. 5):
A.  Make sure king pin sleeve is positioned into the
pivot hub of the A--arm. Sleeve must extend through
the bottom of the hub.
B.  Remove lock  nut and  cap screw  securing the
spindle to the A--arm. Separate spindle from A--arm.
B.  Place thrust washer onto the bottom of the king
pin sleeve. Then place spindle over the A--arm hub,
king pin sleeve and thrust washer.
C. Locate and remove thrust washer from bottom of
kingpinsleeve inA--armandbrakehoseclipfromtop
ofA--arm.RemovekingpinsleevefromA--armifnec-
essary.
NOTE:  Make  sure  cap  screw  is  inserted  down
through the spindle and A--arm hub.
Workman MDE
Page 5 -- 11
Chassis
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 112 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website