Toro 08164SL Service Manual Workman MDE Preface Publication Service

C. Install  brake hose clip  onto cap  screw. Secure
spindle to A--arm hub with cap screw and lock  nut.
Torque fasteners from 75 to 100  ft--lb (102 to 135
N--m).
4.  Slide wheel hub assembly onto spindle. Install outer
bearing, tab washer and jam nut onto spindle.
5.
Rotate the wheel  by hand and tighten  the jam nut
from 75 to 100 in-lb (8.5 to 11.3 N--m) to set the bear-
2.
Install tie rod:
ings. Then, loosen the nut until the hub has end play.
A.  Position tie rod assembly to spindle and pitman
arm so that tie rod groove (LH threads) is orientated
toward the left side of the machine (Fig. 6).
6.  Again, rotate the wheel by hand and tighten the jam
nut from 15 to 20 in-lb (1.7 to 2.3 N--m).
7.
Position nut retainer over jam nut and install  cotter
B.  Insert tie rod ball joints down through the spindle
and up through the Pitman arm. Secure with castle
nuts.
pin through spindle shaft hole. Install dust cap to hub.
8.
Install brake caliper to spindle (see Front Brake Cali-
per in this section).
C. Torque castle nuts from 20 to 25 ft--lb (28 to 33
N--m)tosecure  balljointwhilealigningcastlenutslot
with hole in ball joint stud. If necessary to align holes,
castle nut torque may be slightly more than specifi-
cation. Install cotter pin.
9.
Install wheel assembly with valve stem facing out.
machine to ground.
Torque wheel lug nuts in a crossing pattern from 45
10.Lower
11.
to 65 ft--lb (62 to 88 N--m).
tie rod ball joints and king pin.
steering and toe--in.
sure that front wheels move fully in both direc-
3.
Assemble wheel hub (Fig. 4):
12.Lubricate
A.  If bearing  cups were  removed from  the wheel
hub, press inner  and outer cups  into the hub until
they seat against the hub shoulder.
13.Align
14.Make
B.  Pack both  bearings  with  grease.  Install inner
bearingintothecuponinboardsideofthewheelhub.
tions without contacting any front end components.
IMPORTANT: The   wheel   hub   seal   must  be
pressed in so it is flush with the end of the hub.
The lip of the seal must be toward the inner bear-
ing.
3
2
1
TIE ROD TUBE
C. Lubricate the inside of the new seal and press it
into the wheel hub.
D. If brake rotor was removed, position rotor to hub
withchamfered edgetoward hub.Apply Loctite#242
(or equivalent) tosocket head screws and secure ro-
tor to hub.
Figure 6
1.
2.
Tie rod groove
LH threads
3.   RH threads
Chassis
Page 5 -- 12
Workman MDE
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 112 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website