Toro 08164SL Service Manual Workman MDE Preface Publication Service

Removal (Fig. 1)
Park vehicle  on a level  surface, turn on/off  switch
B.  Position and secure hydraulic brake line to wheel
cylinder (Fig. 3). Torque banjo bolt from 15 to 21 ft--
lb (21 to 28 N--m).
1.
OFF and remove key from the on/off switch.
C. Secure parking brake cable bracket to the brake
actuator lever with clevis pin and cotter pin (Fig. 2).
WARNING
2.
If wheel studs were  removed from wheel hub, use
press to install wheel studs into hub. Make sure to fully
press studs into hub.
Before jacking up the vehicle, review and follow
Jacking Instructions  in Operator’s Manual  and
Chapter 1 -- Safety.
3.
Slide wheel hub onto transaxle shaft.  Install flange
nut to secure wheel hub to the transaxle shaft. Torque
nutfrom125to140ft--lb(170to190N--m).Installcotter
pin.
2.
thegroundusingajackandplaceappropriatejackstand
beneath the rear frame to support vehicle.
Chock wheels not being jacked up. Lift rear wheel off
4.
Slide brake drum onto wheel hub.
NOTE:  To remove brake drum, it may be necessary to
loosen parking brake cable adjustment or remove park-
ing brake cable from brake actuator lever.
3
4
3.
Remove five (5) lug nuts, wheel assembly and brake
drum from the wheel hub.
2
4.
Remove cotter pin and flange nut that secure wheel
hub (item 7) to the transaxle shaft.
5.
6.
Remove wheel hub from transaxle.
1
If necessary, use press to remove wheel studs from
hub.
7.
If necessary,  remove brake  assembly from  trans-
axle:
Figure 2
A.  Remove cotter pin  and clevis  pin securing the
parking brake cable bracket to the brake actuator le-
ver (Fig. 2).
1.
2.
Cotter pin
Clevis pin
3.
4.
Brake cable bracket
Brake actuator lever
2
B.  Clean hydraulic brake line area of rear brake cyl-
inder to prevent contamination. Loosen and discon-
nect hydraulic brake line from  wheel cylinder. Plug
brake line and position it away from wheel cylinder.
1
3
C. Remove  four (4) socket  head screws  and lock
nuts securing the brake assembly to the transaxle.
Remove brake assembly from the transaxle.
4
Installation (Fig. 1)
15
(21
to 21 ft--lb
to 28 N--m)
IMPORTANT:The  parking  brake  actuation  levers
should be  positioned above the  transaxle mount.
When positioned correctly, the levers will point to-
ward the rear of the vehicle (Fig. 2).
5
Figure 3
1.
2.
3.
Brake assembly
Wheel cylinder
Banjo washer
4.
5.
Banjo bolt
Brake line
1.
brake assembly to transaxle.
If brake  assembly was  removed from axle,  install
A.  Secure brake assembly to the transaxle with four
(4)
socket head screws and lock  nuts. Torque lock
nuts from 26 to 30 ft--lb (34 to 41 N--m).
Workman MDE
Page 4 -- 7
Transaxle and Brakes
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 112 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website