Toro 04130SL Rev C Service Manual Multi Pro 5700 D Preface Publication

6.
that secure pump to pump mount bracket.
Remove four (4) flange head screws and flange nuts
9.  Secure  pump  to  mounting  bracket  by  tightening
flange head screws and flange nuts.
7.
8.
from pump  shaft. Locate and  remove key from  pump
shaft.  Remove  set   screws  from  pump  hub.   Clean
threads of set screws and hub.
Remove pump from machine.
10.Position front and rear guard plates to pump mount
bracket.  Install  and  tighten  flange  head  screw  and
flange nut to guard plates. Install flange nuts to secure
guard plates to pump mount bracket.
If needed, loosen set screws in pump hub. Pull hub
11.Install pressure and suction hoses to correct barb fit-
tings (Fig. 7). Secure hoses with hose clamps.
9.
If  needed, remove  pressure dampener,  tee  fitting
(pressure), and elbow fitting (pressure) from pump out-
let (Fig. 8).
10.If
(suction) from pump inlet (Fig. 8).
needed, remove suction dampener and tee fitting
1
2
Installation (Fig. 6)
NOTE:  Coat all spray system o–rings with vegetable oil
before installation to reduce the chance of damage dur-
ing assembly.
1.
Apply PTFE  tape to threads  of removed tee  fitting
(pressure), elbow fitting (pressure), and tee fitting (suc-
tion). Position new o–rings and gaskets on suction and
pressure fittings that were removed during disassembly.
Figure 7
2.
dampener to  pump inlet. Orientate  tee toward rear  of
machine (Fig. 8).
If removed,  install tee  fitting (suction)  and suction
1.
Pressure hose
2.
Suction hose
6
7
6
3.
(pressure),  and  pressure dampener  to  pump  outlet.
Orientate elbow toward rear of machine (Fig. 8).
If removed, install elbow fitting (pressure), tee fitting
8
9
10
4.
to pump shaft. Install  key in shaft and slide pump  hub
onto shaft.
If pump hub was removed, apply anti–seize lubricant
5
4
3
2
11
12  13
14
15
5.
Position pump on pump mounting bracket and install
flange head screws and flange nuts to pump and mount-
ing bracket. Leave fasteners loose.
1
6.
Place coupling spacers into rubber coupling. Install
17
16
cap screws, flat washers, and lock nuts to secure rubber
coupling  to  pump  hub.  Make   sure  that  cap  screw
threads extend through lock nut.
9
Figure 8
7.
If pump  hub was  removed, apply Loctite  #242 (or
equivalent) to threads of  pump hub set screws. Install
set screws into pump hub to secure hub to pump shaft.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Spray pump
10. Pressure dampener
11.  Suction hose (1 1/2”)
12. Hose clamp
Pressure hose (1”)
Hose clamp
Hose barb
13. Nut
8.
Turn  pump shaft  by  hand  and position  pump  on
mounting bracket to  best align the coupling  assembly
between the pump shaft and the hydraulic motor shaft.
Nut
Gasket
Tee fitting (pressure)
Elbow fitting (pressure)
O–ring
14. Seal
15. Tee fitting (suction)
16. Suction dampener
17. Hose barb
Multi Pro 5700–D
Spray System
Page 6 – 11 (Rev. B)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 212 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website