Removal (Fig. 13)
Park machine on a level surface, stop engine, en-
gage parking brake, and remove key from the ignition
switch.
3. Make sure that gasket is properly positioned and
thensecurebrakeassemblytoplanetary(seeBrakeAs-
sembly).
1.
4. Secure wheel motor to planetary with two (2) cap
screws and flat washers. Torque screws 60 ft--lb (81
N--m).
2.
Drain oil from planetary wheel drive/brake assembly
(see Operator’s Manual).
WARNING
CAUTION
Failure to maintain proper wheel lug nut
torque could result in failure or loss of wheel
and may result in personal injury.
When changing attachments, tires, or perform-
ing other service, use correct blocks, hoists,
and jacks. Make sure machine is parked on a
solid, level surface such as a concrete floor.
Prior to raising machine, remove any attach-
ments that may interfere with the safe and
properraisingofthemachine.Alwayschockor
block wheels. Use jack stands or solid wood
blockstosupporttheraisedmachine.Ifthema-
chine is not properly supported by blocks or
jack stands, the machine may move or fall,
which may result in personal injury.
5.
Install wheel assembly with valve stem facing out.
Torque lug nuts from 70 to 90 ft--lb (95 to 122 N--m).
6. Lower machine from jack stands.
7.
Make sure drain plug is installed in bottom of brake
assembly (Fig. 14). Fill planetary wheel drive/brake as-
sembly to proper level with SAE 85W--140 gear lube
(see Operator’s Manual). Capacity is approximately 16
oz. (.47 l) per wheel.
3.
Jacking Instructions in Operator’s Manual). Support
machine with jack stands or solid wood blocks.
Chock front wheels and jack up rear of machine (see
8.
eration (see Operator’s Manual).
Check and adjust brake cables for proper brake op-
4.
5.
Remove rear wheel assembly.
Support wheel motor and brake assembly to prevent
them from shifting during planetary removal.
1
2
6.
Removetwo(2)capscrews andflatwashers thatse-
cure wheel motor to planetary assembly.
7.
Remove four (4) flange head screws that secure
3
brake assembly to planetary assembly (see Brake As-
sembly).
8.
Supportplanetaryassemblytopreventitfromfalling.
Loosen and remove eight (8) flange head screws that
secure planetary assembly to frame. Remove planetary
assembly from machine.
Figure 14
1.
2.
Brake housing
Check plug
3. Drain plug
Installation (Fig. 13)
1.
brake assembly are clean. Position new gasket tobrake
assembly.
Make sure that gasket surfaces of planetary and
2.
Position planetary assembly to machine making
sure to engage splined brake shaft with planetary drive
shaft.Installeight(8)flangeheadscrewstosecureplan-
etary assembly to frame. Torque screws 60 ft--lb (81
N--m).
Multi Pro 5700--D
Page 7 -- 15 Rev. C
Chassis
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5700 D |
| Download File |
|
| Document Type | Catalog |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)