Removal (Fig. 6)
Installation (Fig. 6)
1.
ets to exhaust components.
Install all removed heat shields, hangers and brack•
CAUTION
2.
manifold and exhaust pipe are clean.
Make sure that gasket surfaces on engine exhaust
The muffler and exhaust pipes may be hot. To
avoid possible burns, allow the engine and ex•
haust system to cool before working on the ex•
haust system.
3.
Install exhaust pipe:
A. Position muffler gasket and exhaust pipe to en•
gine exhaust manifold. Install four (4) cap screws
and lockwashers finger tight.
1.
Park machine on a level surface, stop engine, en•
gage parking brake and remove key from the ignition
switch.
B. Position exhaust pipe bracket to engine and
install two (2) cap screws and lock washers finger
tight.
2.
Remove the tailpipe section of the exhaust system:
A. Loosen muffler clamp that secures tailpipe to
muffler.
C. Tighten four (4) cap screws that secure exhaust
pipe to engine exhaust manifold and then tighten two
B. Loosen flange head screw, flange nut and flat
washer that secure tailpipe hanger to machine
frame.
(2)
cap screws that secure exhaust pipe bracket to
engine.
NOTE: Muffler inlet is offset and muffler outlet is cen•
tered.
C. Remove tailpipe from muffler outlet and lower
tailpipe from machine.
4.
inlet (offset) onto exhaust pipe. Support muffler from be•
low.
Slide muffler clamp on exhaust pipe and slide muffler
3.
Remove muffler:
A. Loosen muffler clamp that secures muffler to ex•
haust pipe.
5.
Support muffler from frame with two (2) tailpipe
hangers. Secure each tailpipe hanger to frame with
flange head screw, flat washer and flange nut. Flange
head screws should be placed in middle hole of tailpipe
hangers.
B. Support muffler from below to prevent it from fal•
ling.
C. Remove flange head screws, flange nuts and flat
washers that secure tailpipe hangers to machine
frame.
6.
Place muffler clamp onto front end of tailpipe and
slide tailpipe onto muffler outlet (centered).
D. Slide muffler (with two tailpipe hangers attached)
from exhaust pipe and lower muffler from machine.
7.
Support tailpipe from frame with tailpipe hanger. Se•
cure tailpipe hanger to frame with flange head screw, flat
washer and flange nut. Flange head screw should be
placed in upper hole of tailpipe hanger.
4.
Remove exhaust pipe:
A. Support exhaust pipe to prevent it from falling.
8.
Make sure that tailpipe outlet is parallel to the
ground.
B. Remove two (2) cap screws and lock washers
that secure exhaust pipe bracket to engine.
9.
Tighten muffler clamps to secure exhaust compo•
nents.
C. Remove four (4) cap screws and lockwashers
that secure exhaust pipe flange to engine exhaust
manifold.
D. Lower exhaust pipe from machine.
E. Locate and retrieve muffler gasket.
5.
Remove heat shields, hangers and brackets from
exhaust components as needed.
Multi Pro 5700–D
Page 3 – 9
Kubota Diesel Engine
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5700 D |
| Download File |
|
| Document Type | Catalog |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)