Toro 04130SL Rev C Service Manual Multi Pro 5700 D Preface Publication

Removal (Fig. 34)
Park machine on  a level surface,  stop engine, en•
gage parking brake, and  remove key from the ignition
switch.
5.  Remove  plugs  from  hydraulic  lines,  fittings,  and
ports. Lubricate new o–rings and attach hydraulic hoses
to wheel motor.
1.
6.  If right side wheel  motor was removed, plug speed
sensor connector into machine wiring harness.
CAUTION
7.  Check fluid level in hydraulic oil reservoir and adjust
as required (see Operator’s Manual).
Rotate steering wheel and depress traction ped•
al in both forward and reverse to relieve hydrau•
lic  system pressure  and to  avoid  injury from
pressurized hydraulic oil.
8.  Operate machine and inspect for leaks.
2.
system pressure.
Operate  all hydraulic  controls to  relieve  hydraulic
3
2
3.
Installing Hydraulic System Components at  the begin•
ning of the Service and Repairs section of this chapter.
Read the  General  Precautions for  Removing and
1
Figure 35
1.
2.
Splined brake shaft step
Hydraulic motor end
3.
Planetary assembly end
4.
motor removal, thoroughly clean exterior  of motor and
fittings.
To prevent contamination of hydraulic system during
1
2
NOTE:  To ease reassembly, tag the hydraulic hoses to
show their correct position on the wheel motor.
5.
Disconnect hydraulic  hoses from  fittings on wheel
motor. Put caps or plugs on hydraulic lines, fittings, and
ports to prevent contamination.
6.
speed sensor connector from machine wiring harness.
If right side  wheel motor is being  removed, unplug
3
IMPORTANT: Before  loosening fasteners,  support
wheel motor to prevent motor from falling.
4
7.
Support the pump assembly to prevent it from falling.
Remove two (2) cap screws and flat washers that secure
wheel motor  to brake  and planetary  assemblies. Re•
move wheel motor from machine.
Figure 36
1.
2.
Piston (traction) pump
Top pump fitting
3.
4.
Bottom pump fitting
Case drain fitting
Installation (Fig. 34)
1.
If splined brake shaft  was removed from brake as•
sembly, make sure that the stepped end of the shaft is
aligned toward the hydraulic wheel motor (Fig. 35). Also,
make sure that splines  engage rotating discs in brake
assembly.
2.
Position wheel motor to brake assembly.
3.
Align splines on motor shaft and splined brake shaft.
Slide motor to brake assembly.
4.
Secure  motor to  brake and  planetary  assemblies
with cap screws and flat washers. Torque cap screws 60
ft–lb (81 N–m).
Multi Pro 5700–D
Page 4 – 39
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 212 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website